Paradyne 7110 Скачать руководство пользователя

Страница: 143 / 167

MIB Descriptions

C-32

7110-A2-GB20-00

June 1997

Table C-16.

Generic Interface Test Table Objects (3 of 3)

Object

Setting/Contents

Description

ifExtnsTestResult
(ifExtnsTestEntry
5)

1.3.6.1.3.6.2.1.5
read-only

Contains the result of the
most recently requested
test.

Supports the following values:

none(1) – No test active.

inProgress(3) – Test is in
progress.

notSupported(4) – Requested
test is not supported.

unAbleToRun(5) – Test cannot
run due to the state of the unit.

ifExtnsTestCode
(ifExtnsTestEntry
6)

1.3.6.1.3.6.2.1.6
read-only

Contains a code providing
more specific information
about the test result.

Supports the following values:

none (wellKnownCodes 1) – No
further information is available.
Used for send pattern/code and
loopback tests.

inSyncNoBitErrors
(wellKnownCodes 2) – A monitor
pattern (QRSS or 511) test has
synchronized on the pattern and
has not detected any bit errors.

inSyncWithBitErrors
(wellKnownCodes 3) – A monitor
pattern (QRSS or 511) test has
synchronized on the pattern but
has detected any bit errors.

notInSync (wellKnownCodes 4)
– A monitor pattern (QRSS or 511)
test has not synchronized on the
requested pattern.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды