Paradyne 7110 Скачать руководство пользователя

Страница: 129 / 167

MIB Descriptions

C-18

7110-A2-GB20-00

June 1997

Table C-7.

DS1 Near End Group Configuration Table Objects (3 of 5)

Object, OID, Access

Setting/Contents

Description

dsx1LoopbackConfig
(dsx1ConfigEntry 9 )

1.3.6.1.2.1.1.10.18.6.1.9
read-write

This object specifies the
loopback state of the
network interface.

Applies to the T1 network
interface only.

Supports the following
values:

dsx1NoLoop(1) – The T1
interface is not in a
loopback state.

dsx1PayloadLoop(2) –
Specifies that a Payload
Loopback (PLB) is active
for the network interface.

dsx1LineLoop(3) –
Specifies that a Line
Loopback (LLB) is active
for the network interface.

dsx1OtherLoop(4) –
Specifies that an
unspecified type of
loopback is active for the
network interface.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды