Paradyne 7110 Скачать руководство пользователя

Страница: 113 / 167

MIB Descriptions

C-2

7110-A2-GB20-00

June 1997

The following MIB II groups are not supported:

Address Translation Group

Exterior Gateway Protocol ( EGP ) Group

Generic Receive Address Table

DS1/E1 – RFC 1406

The unit supports DS1/E1 MIB, RFC 1406 for the T1 network interface. The DS1
Near End Group and DS1 Fractional Group are supported for this interface. The
DS1 Near End Group consists of the following tables:

DS1 Configuration, Table C-7

DS1 Current, Table C-8

DS1 Interval, Table C-9

DS1 Total, Table C-10

The DS1 Far End Group is not supported.

RS-232-Like MIB – RFC 1659

The unit supports RS-232-Like MIB, RFC 1659:

Number of RS-232-Like Ports Object.

General Port Table Objects

, Table C-11.

Asynchronous Port Table Objects

, Table C-12. Not supported for the User

Data port.

Synchronous Port Table Objects

, Table C-13. Not supported for the Terminal

port.

Input Signal Table Objects

, Table C-14. Not supported for the Management

port or Terminal port.

Output Signal Table Objects

, Table C-15. Not supported for the Management

port or Terminal port.

Generic Interface Extension MIB

The unit supports the Generic Interface Extension MIB:

Generic Interface Test Table Objects, Table C-16

Enterprise MIB Object

The following Paradyne Enterprise MIB Object is supported by the unit:

Device Configuration Variable

, Table C-17

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды