Paradyne 7110 Скачать руководство пользователя

Страница: 54 / 167

Testing

5-9

7110-A2-GB20-00

June 1997

Data Terminal Loopback

Data Terminal Loopback (DTLB) loops the user data back to the DTE. This
loopback is located as closely as possible to the User Data Port (DTE) interface.

Procedure

To run a data terminal loopback:

1. Position the cursor at the Start command next to Data Terminal Loopback on

the Data Port Tests screen.

2. Press Enter.

3. The Start command is changed to Stop. If you want to manually stop the test,

verify that the cursor is positioned at the Stop command.

DSU

CSU

DTE

Interface

Aggregate

T1
Network
Port

97-15145-01

DTE

Port

Local Loopback

Data Terminal Loopback cannot be started when any other loopback is already
active on the data port.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды