Paradyne 7110 Скачать руководство пользователя

Страница: 49 / 167

Testing

5-4

7110-A2-GB20-00

June 1997

Payload Loopback

Payload Loopback (PLB) loops the received signal on the network interface back
to the network. Framing CRCs and BPVs are corrected.

Procedure

To run a Payload loopback:

1. Position the cursor at the Start command next to Payload Loopback on the

Network Tests screen.

2. Press Enter.

3. The Start command is changed to Stop. If you want to manually stop the test,

verify that the cursor is positioned at the Stop command.

4. Press Enter. The duration of the test is displayed.

496-15076

CSU

DSU

Network

Interface

ALL 1s

PLB

DTE

Payload Loopback cannot be started when any other loopback or Send Pattern
test is already active on the network interface.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды