Paradyne 7110 Скачать руководство пользователя | Manualshive

Страница: 96 / 167

background image

Configuration Option Tables

A-21

7110-A2-GB20-00

June 1997

Table A-9.

Alarms & Traps Options (2 of 2)

SNMP Trap Disconnect

Possible Settings: Enable, Disable
Default Setting: Enable

Determines if a Management port external device connection is dropped after sending
an SNMP trap.

A call established to send out an ASCII alarm always disconnects automatically if
the call was initiated automatically.

Enable – The external device disconnects after sending out an SNMP trap.

Disable – The external device remains connected and must be disconnected by remote
modem or manually. This allows the NMS to poll the DSU/CSU after receiving an SNMP
trap.

Call Retry

Possible Settings: Enable, Disable
Default Setting: Disable

Specify if an unsuccessful call is retried.

Enable – The call is retried up to five times for each ASCII alarm and each SNMP trap.

The following options, Dial-Out Delay Time (min) and Alternate Dial-Out Directory,
affect the amount of time before a retry and the number of retries.

Disable – No retry of an unsuccessful call.

Dial-Out Delay Time (min)

Possible Settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10
Default Setting: 5

This delay applies to both the number of minutes before a new call is initiated for a
different alarm and the number of minutes between call retries. Refer to the previous
option,

Call Retry

.

1 to 10 – Number of minutes before a call is initiated or retried.

Alternate Dial-Out Directory

Possible Settings: None, 1, 2, 3, 4, 5
Default Setting: None

Specifies which alternate dial-out directory to use, if any, when a call cannot be
completed (due to busy, no answer, etc.). This refers to calls initiated for an ASCII alarm
or SNMP trap.

Both Alarm & Trap Dial-Out and Call Retry options must be enabled.

1, 2, 3, 4, or 5 – After attempting to reach the Primary Directory phone number five
times, this alternate dial-out directory phone number will be dialed up to five times.

NOTE:

Refer to the

Call Setup

section of Chapter 3.

None – No alternate phone number is used.

«
...
94
95
96
97
98
...
»

Содержание 7110








































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7110

LinkStick WIS12ABGNX

Бренд: Samsung Страницы: 1

Бренд: Sennheiser Страницы: 1

Бренд: StarTech.com Страницы: 8

Бренд: ZyXEL Communications Страницы: 1

Бренд: GAI-Tronics Страницы: 4

Бренд: Roche Страницы: 2

Бренд: B.E.G. Страницы: 4

Бренд: TP-Link Страницы: 37

Бренд: Aztech Страницы: 2

Бренд: Honeywell Страницы: 2

OneWireless Adapter

Бренд: Honeywell Страницы: 20

Бренд: Honeywell Страницы: 2

Бренд: Honeywell Страницы: 54

Бренд: Honeywell Страницы: 2

Home C-Wire Adapter

Бренд: Honeywell Страницы: 24

Бренд: Honeywell Страницы: 54

OWA 100 OneWireless

Бренд: Honeywell Страницы: 33

Бренд: RocketFish Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды