Panasonic SC-HG1-C Скачать руководство пользователя страница 43

Страница: 43 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-9

■

Remote output RY (Mode 1 master station → Communication unit)

This is a write-only register for output from the master station to the communication unit in units

of bits.

Before using mode 1, be sure to configure the “page” settings.

For details, refer to

“Page settings”

<Remote output RY>

+00

Sensor response data switching request

Not used

Command

request

Not used Error

code Not used Command

Sensor

head

value

Calcu-

lated

value

Normal

mea-

sured

value

Judg-

ment

value

Write

flag

Send

request

+10

Not used

Page

Page 3 Page 2 Page 1

+20 Not used

External input 1 (IN1)

Slave

unit 14

Slave

unit 13

Slave

unit 12

Slave

unit 11

Slave

unit 10

Slave

unit 9

Slave

unit 8

Slave

unit 7

Slave

unit 6

Slave

unit 5

Slave

unit 4

Slave

unit 3

Slave

unit 2

Slave

unit 1

Master

unit

+30 Not used

External input 2 (IN2)

Slave

unit 14

Slave

unit 13

Slave

unit 12

Slave

unit 11

Slave

unit 10

Slave

unit 9

Slave

unit 8

Slave

unit 7

Slave

unit 6

Slave

unit 5

Slave

unit 4

Slave

unit 3

Slave

unit 2

Slave

unit 1

Master

unit

+40 Not used

External input 3 (IN3)

Slave

unit 14

Slave

unit 13

Slave

unit 12

Slave

unit 11

Slave

unit 10

Slave

unit 9

Slave

unit 8

Slave

unit 7

Slave

unit 6

Slave

unit 5

Slave

unit 4

Slave

unit 3

Slave

unit 2

Slave

unit 1

Master

unit

+50

Not used

+60

+70

Not used

Error clear

request

Setting

initial-

ization

request

Initializa-

tion done

Not used

<Setting details>

Name

Device No.

Description

Command request

Send request

RY[00]

Send command to controller request bit.

When this bit is set, a command is sent.

To send a subsequent command, clear the bit and then set again.

Write flag

RY[01]

To execute a read command, clear this bit.

To execute a write command, set this bit.

RY[00]: Set before a send request.

Sensor response data switching request (*1) (*2)

Judgment value

(*3)

RY[08]

Change to judgment value mode.

When the bit is set, the mode changes to judgment value mode.

Normal mea-

sured value (*3) RY[09]

Change to normal measured value mode.

When the bit is set, the mode changes to normal measured value mode.

Calculated value

(*3)

RY[0A]

Change to calculated value mode.

When the bit is set, the mode changes to calculated value mode.

Sensor head

value (*3)

RY[0B]

Change to sensor head value mode.

When the bit is set, the mode changes to sensor head value mode.

Command

RY[0C]

Change to command mode.

When this bit is set, changing to command mode and sending com-

mands is allowed.

Set before a command request (RY[00]: send request).

Error code

RY[0E]

Change to error mode.

When this bit is set, the mode changes to error mode.

Page1 to page3

(*4) (*5)

RY[10] to [12]

Changes the controller assignment in the memory map.

When this bit is set, the controller assignment changes to the assign-

ment of the set page settings.

External input 1

(IN1) (*6)

RY[20] to [2E]

Controls external input 1 on the controller.

When this bit is set, external input 1 turns ON.

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 43 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: