Panasonic SC-HG1-C Скачать руководство пользователя страница 86

Страница: 86 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-52

<Write command sending procedure>

This section explains the procedure for using the command transmission function to write set-

ting information to a controller.

The example of sending the LOW set value command “0x0014” (write) to a master unit and

slave units 1 to 3 is used.

is only set when the operation mode is CC-Link mode 1.

RX[7B] (*1)

Check remote ready flag

RX[0C]

Check command flag

RY[0C]

Command flag

RWw[00]

Set command request

sensor

RY[01]

Write flag

RWw[01]

Set command code

RY[10]

Page 1 settings

RX[10]

Check page 1 settings

0x000F

0x0014

When operation mode is CC-Link mode 1

Write mode

RY[00]

Send request flag

RX[00]

Check send done flag

RWr[01]

Check command

response code

RWr[00]

Check command

response sensor

RWr[02] to [09]

Check sensor response data

RX[7A] (*2)

Check error status flag

RX[01]

Check error flag

0x0000

0x000F

0x0000

0x0014

RWw[02] to [09]

Set command data

LOW set value (master unit + 3 slave units)

0x00000000

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 86 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: