Panasonic SC-HG1-C Скачать руководство пользователя страница 104

Страница: 104 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-70

●

HG-TC

series

For details on Response Parameter adress, refer to

“4-10-2 HG-T series command list”

Response parameter

Measures

Error code (Note 1) measurement alarm

(Note 1)

Notifi

cation

Sensor head unconnected

Status check

E200

–

Connected sensor head incompat-

ible

Status check

E230

–

Connected unit count check error

Status check

E160

(For master units only) –

NPN / PNP output type mixture error Status check

E100

(For master units only) –

Calculated unlit count error

Status check

E110

(For master units only) –

Copy executionerror

( Slave unit problem)

Status check

E170

(For master units only) –

Detection capability limit (obtained

edge information) (Note 2)

Sensing object check

–

Measurement alarm 1

The amount of entering light is too

much due to the influences of ambi

ent light, etc. (Note 2)

Status check

–

Measurement alarm 1

The amount of entering light de-

creases due to stain on the detection

surface, beam axis misalignment, etc.

Sensing object check

–

Measurement alarm 2

The specified measurement direc

tion differs from the insertion direc

tion of the detected object

Status check /

Sensing object check –

Measurement alarm 2

Cau-

tion

Controller cumulative run time limit

exceeded(87,600 hours)

Controller replacement –

–

Sensor head cumulative run time

limit exceeded (87,600 hours)

Sensor head replacement –

–

Controller memory saving count limit

exceeded (1,000,000 times)

Controller replacement –

–

Sensor head memory saving count

limit exceeded

(for receivers only, 1,000,000 times)

Sensor head replacement –

–

Fault

Controller memory function damaged Controller replacement E600 / E610 / E620 –
Sensor head memory function damaged Sensor head replacement E630 (For receivers only)

E640 (For emitters only) –

Output section short-circuit error

Status check /

Replacement

E700

–

Detection circuit damaged

Sensor head replacement E240

–

System error

Controller replacement E900 / E910 / E911 /

E912 / E920

–

Notes: 1) Error codes and alarms are displayed on

HG-TC

□ controllers.

2) If “Alarm condition selection (ALM.CND)” is set to “Hold last value (HOLD)”, Measurement alarm 1 is

not notified.

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 104 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: