Panasonic SC-HG1-C Скачать руководство пользователя страница 119

Страница: 119 / 128

Troubleshooting

WUME-SCHG1C-4

8-3

Check that RX[7B]: remote ready flag (*1) is set.

Set RY[0C]: command flag and then check that RX[0C]: command flag is set. This changes

the mode to command mode. Clear sensor response data switching request flags other than

the command flag in advance.

Set the RY[01]: write flag and activate Write mode.

If the operation mode is CC-Link mode 1, set RY[10]: page 1. Page 1 settings are request-

ed, and RX[10]: page 1 is set. In CC-Link mode 1, always configure the page settings.

The page settings of the sensor response data (master unit, slave units 1 to 14) are as

shown in the table below.

Sensor response data

RY[10]

RY[11]

RY[12]

Master unit, slave units 1 to 6

Slave units 7 to 13

Slave unit 14

Specify the controller to which the command will be sent with RWw[0]: command request

sensor.

Set the command code to be sent to RWw[1].

Set the command data to be sent to RWw[2] to [9].

Set RY[00]: send request flag and send the command. When command transmission is

completed, RX[00]: send done flag is set. Verify that RX[00]: send done flag is set, and then

proceed with the steps below.

Verify that a communication error has not occurred with the RX[7A]: error status flag (*2)

cleared. If a communication error has occurred, refer to

“8-2 Communication errors”

10.

Because a command error occurred, RX[01]: error flag is set. Among the RX[60] to [6F] error

output flags, the bit corresponding to the controller in which the error occurred is set at the

same time.

11.

The value specified in step

(master unit, slave unit 1, slave unit 2, slave unit 3: 0x000F) is

set in RWr[0]: command response sensor. The command code sent to RWr[1] is stored.

12.

The error code is stored in the sensor response data of the RWr that corresponds to the

controller in which the command error occurred.

13.

The sensor response data of RWr that correspond to controllers in which a command error

did not occur is "0".

14.

Clear RY[00]: send request flag. The communication unit ends command transmission, and

RX[00]: send done flag and RX[01]: error flag are cleared. RX[60] to [6F] error output flags

are also cleared.

15.

If the operation mode is CC-Link mode 1, clear RY[10]: page 1. Page 1 settings are

cleared, and RX[10]: page 1 is cleared.

16.

Clear RY[01]: write flag.

17.

Clear RY[0C]: command flag. The communication unit exits command mode, and RX[0C]:

command flag is cleared. After removing the cause of the error, re-execute the command.

*1: The bit position depends on the operation mode.

CC-Link mode 1: RX[7B], CC-Link mode 2: RX[17B], CC-Link mode 3: RX[1BB]

*2: The bit position depends on the operation mode.

CC-Link mode 1 : RX[7A], CC-Link mode 2: RX[17A], CC-Link mode 3: RX[1BA]

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 119 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: