Panasonic SC-HG1-C Скачать руководство пользователя страница 103

Страница: 103 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-69

4-14-2 Statuses and Measures

The statuses judged by the self-monitoring function are classified into the following four categories.

When the status is “notification”, “caution”, or “fault”, you must check the installation state or

maintain or replace the product.

Status

Description

Remarks

Normal

Normal state

The device is operating normally.

Notification

Unstable detection state

Review the settings.

Caution

State in which the device must be replaced The device has almost reached its service life.

Fault

State in which the device is uncontrollable

The device is short-circuited or broken.

If “notification”, “caution”, or “fault” status is notified, take measures as shown in the following table.

●

HG-SC

series

For details on Response Parameter adress, refer to

“4-10-1 HG-S series command list”

Response parameter

Measures

Error code (Note)

Alarm (Note)

Notifi

cation

Sensor head unconnected

Status check

E200

–

Connected unit count check error

Status check

E160

(For master units only) –

NPN / PNP output type mixture error Status check

E100

(For master units only) –

Calculated unlit count error

Status check

E110

(For master units only) –

Copy executionerror

( Slave unit problem)

Status check

E170

(For master units only) –

The thrust on the sensor head stroke

is above the specified range.

Status check

E210

–

Pressure check

Status check

–

Alarm

Catch check

Status check

–

Alarm

Fault

Controller memory function damaged Controller replacement E600 / E610 / E620 –

Sensor Head memory function dam-

aged

Sensor head replacement E630

–

Output section short-circuit error

Status check /

Replacement

E700

–

Detection circuit damaged

Sensor head replacement E240

–

System error

Controller replacement E900 / E910 / E911 /

E912 / E920

–

Note: Error codes and alarms are displayed on

HG-SC

□ controllers.

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 103 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: