Panasonic SC-HG1-C Скачать руководство пользователя страница 121

Страница: 121 / 128

Troubleshooting

WUME-SCHG1C-4

8-5

Error code

Description

Action

DEC

HEX

3100

0x0C1C More than 14 controllers / slave units are con-

nected.

The maximum number of controllers / slave

units that can be connected is 14. Check

the number of connected controllers / slave

units.

3200

0x0C80 CC-Link communication is not taking place. The data link was broken. Check the con-

nection state of the connectors.

4095

0x0FFF Request not accepted because the controller

was busy processing a command.

Another command was requested while the

controller was busy processing a previous

command. Wait until controller processing

finishes before requesting a command.

Note: This product cannot detect errors that occur in a controller.

To check the error code in a controller, use a 0x0001 command (status / error) in command mode to read

the error code.

8-2 Communication errors

If an error occurs, set RY[7A]: clear error request (*1) to clear the error state.

If the error does not clear when RY[7A]: clear error request (*1) is set and RX[7B]: remote ready

flag (*2) does not set, check the state of the connection with the communication unit and then

restart.

RX[7A] (*3)

Error status flag

RX[7B] (*2)

Check remote ready flag

RY[7A] (*1)

Set an error clear request

RX[6F]

Communication unit error

flag

Check that RX[7B]: remote ready flag (*2) is cleared and RX[7A]: error flag (*3) is set.

RX[6F]: communication unit error flag indicates whether or not an error state is due to a

problem in the communication unit. If the problem is in the communication unit, RX[6F]: com-

munication unit error flag is set.

Set RY[7A]: clear error request (*1). This operation causes the communication unit to clear

RX[7A] (*3): error status flag and sets RX[7B] (*2): remote ready flag. At this time, if RX[6F]:

communication unit error flag is set, RX[6F]: communication unit error flag will also be

cleared. (*4)

If RX[7B]: remote ready flag is not set when the above operation is performed, this indicates

that the error was caused by a problem that does not allow recovery by operation. In this

event, remove the cause of the error and cycle the power OFF - ON.

Clear RY[7A]: clear error request (*1).

*1: The bit position depends on the operation mode.

CC-Link mode 1: RY[7A], CC-Link mode 2: RY[17A] CC-Link, mode 3: RY[1BA]

*2: The bit position depends on the operation mode.

CC-Link mode 1: RX[7B], CC-Link mode 2: RX[17B], CC-Link mode 3: RX[1BB]

*3: The bit position depends on the operation mode.

CC-Link mode 1: RX[7A], CC-Link mode 2: RX[17A], CC-Link mode 3: RX[1BA]

*4: You can enter error mode and check the error code.

For details on error mode, refer to

“4-9 Error mode”

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 121 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: