Panasonic SC-HG1-C Скачать руководство пользователя страница 68

Страница: 68 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-34

4-10 Commands

4-10-1 HG-S series command list

The following table shows the command parameters that are used to read and write controller

settings and statuses and to send operation commands to controllers.

For details on each item, refer to the

“HG-S User’s Manual”

Attributes (R: Read, W: Write, R/W: Read/Write)

Command

Attribute

Name

Response/Setting parameter

HG-S

Series

0x0001

Status/Error

When status is normal = 0

When error occurs = Error code

0x0002 to 0x0004

System reserved

Do not use.

0x0005

Controller reset

Reset the controller. (Master unit only)

0x0006

Initialization (RESET)

Return the settings to the factory default state.

Do not specify "0".

0x0007 to 0x000F

System reserved

Do not use.

0x0010

Judgment value (JUDGE.V)

Integer indicating minimum resolution units of controller.

-1999999 to 1999999

0x0011

Normal measured value

(NORM.V)

Integer indicating minimum resolution units of controller.

-1999999 to 1999999

0x0012

Calculated value (CALC)

Integer indicating minimum resolution units of controller.

If a calculated value is not set, the judgment

value is output.

-1999999 to 1999999

0x0013

Sensor head measured value

(HEAD.V)

Integer indicating minimum resolution units of controller.

-1999999 to 1999999

0x0014

R/W LOW set value (LO.SET)

Integer indicating minimum resolution units of controller.

-1999999 to 1999999

0x0015

R/W HIGH set value (HI.SET)

Integer indicating minimum resolution units of controller.

-1999999 to 1999999

0x0016 to 0x0017

System reserved

Do not use.

0x0018

R/W Hysteresis (HYSTER)

Integer indicating minimum resolution units of controller.

0 to 1999999

0x0019

System reserved

Do not use.

0x001A

R/W Output operation (OUTPUT)

0: N.O.

1: N.C.

0x001B

System reserved

Do not use.

0x001C

Output state

bit0: External output 1 (0 = OFF / 1 = ON)

bit1: External output 2 (0 = OFF / 1 = ON)

bit2: External output 3 (0 = OFF / 1 = ON)

The high bit is “0”.

0x001D

Input state

bit0: External input 1 (0 = OFF / 1 = ON)

bit1: External input 2 (0 = OFF / 1 = ON)

bit2: External input 3 (0 = OFF / 1 = ON)

The high bit is “0”.

0x001E

Execute bank load (LOAD)

Bank numbers 1 to 3 are loaded

0x001F

Execute bank save (SAVE)

Bank numbers 1 to 3 are saved

0x0020

R/W Key lock (LOCK)

0: Key lock OFF

1: Key lock ON

0x0021

R/W Eco mode (ECO)

0: Eco mode OFF

1: Eco mode ON

0x0022

Maximum value during P-P

measurement

Integer indicating minimum resolution units of controller.

If the measurement mode is not P-P or P-P/2, a

judgment value is output.

-1999999 to 1999999

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 68 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: