Panasonic SC-HG1-C Скачать руководство пользователя страница 87

Страница: 87 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-53

Check that RX[7B]: remote ready flag (*1) is set.

Set the RY[0C]: command flag. This puts the communication unit in command mode, and

the RX[0C]: command flag is set. Clear sensor response data switching request flags other

than the command flag in advance.

Set the RY[01]: write flag and activate Write mode.

If the operation mode is CC-Link mode 1, set RY[10]: page 1. Page 1 setting is requested,

and RX[10]: page 1 is set. In CC-Link mode 1, always configure the page settings.

The page settings of the sensor response data (master unit, slave units 1 to 14) are as

shown in the table below.

Sensor response data

RY[10]

RY[11]

RY[12]

Master unit, slave units 1 to 6

Slave units 7 to 13

Slave unit 14

Specify the controller to which the command will be sent with RWw[00]: command request

sensor. When the operation mode is CC-Link mode 1, take care not to specify a command

request sensor outside the specified page setting range.

Set the command code to be sent to RWw[01].

Set the command data to be sent to RWw[02] to [09].

Set RY[00]: send request flag and send the command. When command transmission is

completed, RX[00]: send done flag is set. Verify that RX[00]: send done flag is set, and then

proceed with the steps below.

Verify that a communication error has not occurred with the RX[7A]: error status flag (*2)

cleared. If a communication error has occurred, refer to

“8-2 Communication errors”

10.

Verify that a command error has not occurred with the RX[01]: error flag cleared. If a com

mand error has occurred, refer to

“8-1 Command error”

11.

The value specified in step

(master unit, slave unit 1, slave unit 2, slave unit 3: 0x000F) is

set in RWr[00]: command response sensor. The command code sent to RWr[01] is stored.

12.

The RWr sensor response data is “0”.

13.

Clear RY[00]: send request flag. The communication unit ends command transmission, and

the RX[00]: send done flag is cleared.

14.

If the operation mode is CC-Link mode 1, clear RY[10]: page 1. Page 1 settings are

cleared, and RX[10]: page 1 is cleared.

15.

Clear RY[01]: write flag.

16.

Clear RY[0C]: command flag. The communication unit exits command mode, and RX[0C]:

command flag is cleared.

*1: The bit position depends on the operation mode.

CC-Link mode 1: RX[7B], CC-Link mode 2: RX[17B], CC-Link mode 3: RX[1BB]

*2: The bit position depends on the operation mode.

CC-Link mode 1: RX[7A], CC-Link mode 2: RX[17A], CC-Link mode 3: RX[1BA]

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 87 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: