Panasonic SC-HG1-C Скачать руководство пользователя страница 88

Страница: 88 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-54

4 -11 Reading received light waveforms (For the HG-T only)

When reading received light waveforms, select measured waveforms, reference waveforms,

or waveforms during beam axis adjustment (Note 1), so that you can read waveform data and

other information.

Note: For details on waveforms during beam axis adjustment, refer to

“4-12 Registering the reference wave-

form (For the HG-T only)”

4-11-1 Format of received light waveform

Reading received light waveforms makes it possible to obtain simplified received light wave

forms that represent the maximum received light width (CMOS cell) of the receiver by 256 areas

(0 to 255) and the received light intensity by 256 gradations (0 to 255).

●

Measurement start point and measurement end point

Measurement start points and measurement end points can be obtained only in reference

waveform acquisition mode. Obtaining the measurement start point and measurement end point

makes it possible to know the range that is used for measurement within the simplified received

light waveform.

Measurement

range

Light receiving area

255

BOTTOM side

TOP side

Measurement

start point

Received

light intensity

Measurement

end point

●

Edge information and edge position

Edge information can be obtained as information indicating a rising edge or falling edge at each

edge position (edge information 1) and effective edge mode information (edge information 2).

Edge positions are points on the borderline between light interception and light entry within the

received light intensity waveform when a measured object is inserted. The edge position on the

top side is 0.

TOP side

255

BOTTOM side

Edge position 0

Edge information 1: Falling edge

Edge information 2: Only one edge enabled

255

Received

light intensity

Judgment

level

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 88 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: