Panasonic SC-HG1-C Скачать руководство пользователя страница 26

Страница: 26 / 128

Installation and Settings

WUME-SCHG1C-4

3-4

3-2-2 Communication unit settings

After changing the settings, be sure to turn the power OFF and then ON.

Follow the procedure below to configure the settings.

Set the station number (1 to 64) with the station number setting switch.

Station number setting switch

Note: If you set the station number setting switch to 0 or 65 or higher, an error will occur.

Set the communication speed with the communication speed setting switch.

SW No. Communication speed

156kbps

(Factory default state)

625kbps

2.5Mbps

5Mbps

10Mbps

Communication speed setting switch

Set the communication method and number of occupied stations with the mode setting

switch.

When you have completed the mode setting switch settings, attach the switch cover.

Mode setting switch

Switch cover

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 26 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: