Panasonic SC-HG1-C Скачать руководство пользователя страница 94

Страница: 94 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-60

■

Examples of sent commands

Send the “Waveform read setting” command (WRITE) to set the waveform type.

(Command code: 0x0370)

Send this command only for the first time after starting the communication unit or when

switching the type of the waveform to be read.

Write data

High

Low

Bit15 Bit14 Bit13 Bit12 Bit11 Bit10

Bit9 Bit8 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0

Reserved (Always write 0x01.)

Waveform type

Bit7 to

Bit0

Select a waveform type.

0x00: Reference waveform

Send the “Waveform read setting” command (READ). (Command code: 0x0370)

If the response is normal, the following response data will be returned.

Read data

High

Low

Bit15 Bit14 Bit13 Bit12 Bit11 Bit10 Bit9

Bit8

Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0

Reserved

Status Reserved Waveform type (0x00: Reference waveform)

Bit9

Status

1: Waveform information has been saved

0: Waveform information has not been saved

(For example, immediately after the unit

starts up, operation mode is changed, or

measured values are reset)

Send the “Waveform read data” command (READ). (Command code: 0x0371 to 0x03B0)

The “Waveform read data” command can obtain four bytes of received light data by using

a single address. Reference waveform data can be obtained by sending command codes

from 0x0371 through to 0x03B0 in this order and then concatenating the data obtained.
If the response is normal, the following response data will be returned.
<Example: When the command code is 0x0371>

Read data

Received light intensity [0]

0x00 to 0xFF

Received light intensity [1]

0x00 to 0xFF

Received light intensity [2]

0x00 to 0xFF

Received light intensity [3]

0x00 to 0xFF

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 94 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: