Panasonic SC-HG1-C Скачать руководство пользователя страница 78

Страница: 78 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-44

Command

Attribute

Name

Response/Setting parameter

HG-T

Series

0x031C

R/W Display switching mode

0: Normal measured value

1: Calculated value (during calculation)

2: Label

3: LOW set value

4: HIGH set value

5: Sensor head measured value

6: Work insertion direction (Note 2)

0x031D

Controller cumulative run time

(RUN.TIM)

Units of 1 hour

0x031E

Sensor head cumulative run

time (HD.TIME)

Units of 1 hour

0x031F to 0x0322

System reserved

Do not use.

0x0323

R/W Connected unit count check

(CON.CHK)

0: OFF

1: ON

0x0324

R/W Key lock (KEYLOC)

0: MANUAL

1: AUTO

0x0325

R/W Reverse insertion check

(DIR.CHK)

0: OFF

1: ON

0x0326

Work insertion direction state

(Note 2)

• Auto edge detection mode

0: TOP

1: BOTTOM

2: Indeterminate

• Edge detection mode, center position detection

mode

0: TOP

1: BOTTOM

2: Indeterminate

• External form / width detection mode, inside

diameter / gap detection mode

2: Indeterminate

0x0327 to 0x035F

System reserved

Do not use.

0x0360

Beam axis adjustment mode

start

Start beam axis adjustment.

Specify "0".

Always send during measurement.

0x0361

Beam axis adjustment status

bit0 to bit12: Reserved

bit15 bit14 bit13

Beam axis state

0 Immediately after beam axis

adjustment starts

1 Beam axis aligned state

0 Receiver has shifted toward

TOP side (emitter has shifted

toward BOTTOM side)

1 Receiver has shifted toward

BOTTOM side (emitter has

shifted toward TOP side)

0 Beam axis is completely out of

position (fully blocked state)

1 The light intensity is too much

0 The light intensity is too little

1 Objects intercepting light or

stains (adhering substances)

exist inside measurement area

0x0362

Reference waveform registra-

tion execution

Execute reference waveform registration.

Specify "0".

Always send with beam axis in aligned state

0x0363

Reference waveform registra-

tion status

0: Registration completed

1: Registration failed

2: Registering

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 78 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: