Panasonic SC-HG1-C Скачать руководство пользователя страница 77

Страница: 77 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-43

Command

Attribute

Name

Response/Setting parameter

HG-T

Series

0x0309

R/W Alarm state selection

(ALM.CND)

0: HOLD (hold previous value)

1: ALARM (alarm output)

0x030A to 0x030B

System reserved

Do not use.

0x030C

R/W Stain check (STA.CHK)

0: Stain check OFF (OFF)

1: Low sensitivity setting ON (LOW)

2: High sensitivity setting ON (HIGH)

3: User setting ON (USER)

0x030D

R/W Stain threshold (STA.THR)

50 to 95

0x030E

R/W Hold setting (HOLD)

Set the sum of the values below according to

the states of the measurement mode and trigger

mode settings.

• Measurement mode (MEAS)

0x0000 = Sample hold

0x1000 = Peak hold

0x2000 = Bottom hold

0x3000 = Peak to peak hold

0x4000 = Peak to peak hold P-P/2

0x5000 = NG hold

• Trigger mode (TRIG)

0x000 = One-shot

0x100 = Hold

0x030F to 0x0315

System reserved

Do not use.

0x0316

R/W

Calculation mode (MODE) /

Calculation application selec-

tion (APPLI)

0: No calculation

1: Maximum value (MAX)

2: Minimum value (MIN)

4: Average value (AVERAG)

5: Standard difference (STAND)

8: Thickness/Width (THICK)

0x0317

R/W Copy select individual

(CPY.SEL)

0 = Not target / 1 = Target

For each target, set the bit to 0 or 1.

Bit 0: Operation mode selection

Bit 1: Measurement direction

Bit 2: HIGH set value

Bit 3: LOW set value

Bit 4: Hysteresis

Bit 5: Teaching type

Bit 6: Tolerance setting

Bit 7: Preset value

Bit 8: Preset data selection

Bit 9: Preset save

Bit 10: Reference waveform save

Bit 11: Average count

Bit 12: Output pattern

Bit 13: Analog output selection

Bit 14: Hold setting

Bit 15: External input

Bit 16: External output

Bit 17: External output delay timer selection

Bit 18: Number of digits displayed

Bit 19: Eco mode

Bit 20: Alarm

Bit 21: Key lock setting selection

0x0318

System reserved

Do not use.

0x0319

Copy execution (CPY.EXE)

Execute copying.

Specify "0".

0x031A

R/W Copy lock (LOCK)

0: Copy lock OFF

1: Copy lock ON

0x031B

R/W Bank save selection

(BNK.DAT)

0: All

1: HIGH set value, LOW set value

2: HIGH set value, LOW set value, preset value

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 77 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: