Panasonic SC-HG1-C Скачать руководство пользователя страница 66

Страница: 66 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-32

If the operation mode is CC-Link mode 1, set RY[10]: page 1. Page 1 setting is requested,

and RX[10]: page 1 is set. In CC-Link mode 1, always configure the page settings.

The page settings of the sensor response data (master unit, slave units 1 to 14) are as

shown in the table below.

Sensor response data

RY[10]

RY[11]

RY[12]

Master unit, slave units 1 to 6

Slave units 7 to 13

Slave unit 14

Verify that a communication error has not occurred with the RX[7A]: error status flag (*3)

cleared. If a communication error has occurred, refer to

“8-2 Communication errors”

After the initial measurement data wait time, the judgment values are repeatedly stored in an

area equivalent to master unit + three slave units of RWr[02] to [09]: sensor response data.

The measurement data update cycle is indicated in the table below.

Measurement mode

Update cycle (ms)

Judgment value

Normal measured value

Calculated value

Sensor head value

The first time measurement data is saved, a wait time occurs. In addition to the update cy

cle, the actual update time will increase due to the CC-Link settings (baud rate and number

of refresh points) and the device environment.

*1: The bit position depends on the operation mode.

CC-Link mode 1: RX[7B], CC-Link mode 2: RX[17B], CC-Link mode 3: RX[1BB]

*2: If all sensor response data switching requests are cleared, the mode will default to judgment value read

mode and RX[08]: judgment value flag will be set.

*3: The bit position depends on the operation mode.

CC-Link mode 1: RX[7A], CC-Link mode 2: RX[17A], CC-Link mode 3: RX[1BA]

*4: If the remote ready flag was cleared, the values may not be correctly acquired. Periodically check if the re

mote ready flag is set.

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 66 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: