Panasonic SC-HG1-C Скачать руководство пользователя страница 39

Страница: 39 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-5

4-3 Memory map

4-3-1 CC-Link mode 1

■

Remote input RX (Mode 1 communication unit → Master station)

This is a read-only register for input from the communication unit to the master station in units of

bits.

Values cannot be written to this register.

Before using mode 1, be sure to configure the “page” settings.

For details, refer to

“Page settings”

<Remote input RX>

+00

Sensor response data switching response

Not used

Command

response

Not used Error

code Not used Command

Sensor

head

value

Calcu-

lated

value

Normal

mea-

sured

value

Judg-

ment

value

Error

flag

Send

response

+10

Not used

Page

Page 3 Page 2 Page 1

+20

Not used

Judgment output 1 (OUT1)

Slave

unit 14

Slave

unit 13

Slave

unit 12

Slave

unit 11

Slave

unit 10

Slave

unit 9

Slave

unit 8

Slave

unit 7

Slave

unit 6

Slave

unit 5

Slave

unit 4

Slave

unit 3

Slave

unit 2

Slave

unit 1

Master

unit

+30

Not used

Judgment output 2 (OUT2)

Slave

unit 14

Slave

unit 13

Slave

unit 12

Slave

unit 11

Slave

unit 10

Slave

unit 9

Slave

unit 8

Slave

unit 7

Slave

unit 6

Slave

unit 5

Slave

unit 4

Slave

unit 3

Slave

unit 2

Slave

unit 1

Master

unit

+40

Not used

Judgment output 3 (OUT3)

Slave

unit 14

Slave

unit 13

Slave

unit 12

Slave

unit 11

Slave

unit 10

Slave

unit 9

Slave

unit 8

Slave

unit 7

Slave

unit 6

Slave

unit 5

Slave

unit 4

Slave

unit 3

Slave

unit 2

Slave

unit 1

Master

unit

+50

Not used

Alarm output

Slave

unit 14

Slave

unit 13

Slave

unit 12

Slave

unit 11

Slave

unit 10

Slave

unit 9

Slave

unit 8

Slave

unit 7

Slave

unit 6

Slave

unit 5

Slave

unit 4

Slave

unit 3

Slave

unit 2

Slave

unit 1

Master

unit

+60

Error output

Commu-

nication

unit

Slave

unit 14

Slave

unit 13

Slave

unit 12

Slave

unit 11

Slave

unit 10

Slave

unit 9

Slave

unit 8

Slave

unit 7

Slave

unit 6

Slave

unit 5

Slave

unit 4

Slave

unit 3

Slave

unit 2

Slave

unit 1

Master

unit

+70

Not used

Remote

ready

Error

state

Setting

initializa-

tion done

Initial-

ization

request

Not used

<Setting details>

Name

Device No.

Description

Command response

Send response

RX[00]

RY[00]: Response bit to a send request.

This bit is set when transmission of a command to a controller is completed.

Error flag

RX[01]

This bit is set when the command response from a controller is an error.

Sensor response data switching response (*1)(*2)

Judgment value

(*3)

RX[08]

RY[08]: Response bit to a judgment value.

This bit is set when judgment value mode is entered.

Normal mea-

sured value (*3) RX[09]

RY[09]: Response bit to a normal measured value.

This bit is set when normal measured value mode is entered.

Calculated value

(*3)

RX[0A]

RY[0A]: Response bit to a calculated value.

This bit is set when calculated value mode is entered.

Sensor head

value (*3)

RX[0B]

RY[0B]: Response bit to a sensor head value.

This bit is set when sensor head value mode is entered.

Command

RX[0C]

RY[0C]: Response bit to a command.

This bit is set when command mode is entered.

Error code

RX[0E]

RY[0E]: Response bit to an error code.

This bit is set when error mode is entered.

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 39 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: