Panasonic SC-HG1-C Скачать руководство пользователя

Страница: 96 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-62

4-12 Registering the reference waveform (For the HG-T only)

The following flowchart shows the procedure for reading and registering waveforms to register

the reference waveform.

To register the reference waveform, you must invoke beam axis adjustment mode.

■

Flowchart of reference waveform registration

3. "Waveform read setting" (READ)

The command saves the current waveform

information into the controller.

2. "Waveform read setting" (WRITE)

The command selects a waveform type

(waveform during beam axis adjustment).

1. "Beam axis adjustment startup" (WRITE)

4. "Waveform read data" (READ)

The command reads waveform data.

5-1. “Beam axis adjustment status at the

time of waveform reading” (READ)

5-2. “Beam axis adjustment status”

(READ)

reference

waveform

Do not register

the reference

waveform

To register the

reference wave-

form without

checking wave-

forms

To register the

reference wave-

form while check-

ing waveforms

(Note 1)

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Похожие инструкции для SC-HG1-C

Бренды по названию

Популярные бренды

Panasonic SC-HG1-C, Руководство пользователя

Результаты поиска

Содержание SC-HG1-C

Отзывы:

Похожие инструкции для SC-HG1-C

Бренды по названию

Популярные бренды