Panasonic SC-HG1-C Скачать руководство пользователя страница 100

Страница: 100 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-66

To check whether the reference waveform has been registered after registering it, send the

“Reference waveform registration status” command (READ). (Command code: 0x0363)

If the response is normal, the following response data will be returned.

Read data

High

Low

Bit15 Bit14 Bit13 Bit12 Bit11 Bit10

Bit9 Bit8 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0

Reserved

Status

Details of “Status”

The "Reference waveform registration execution" command (WRITE) that was executed last time is

successful.

The "Reference waveform registration execution" command (WRITE) that was executed last time is

unsuccessful and the reference waveform status has not been updated from the previous state.

(If the power is turned OFF and then ON, the history of beam axis adjustment failures will be erased.)

Reference waveform registration is in progress.

To quit beam axis adjustment mode without registering the reference waveform, send the

“Beam axis adjustment end” command (WRITE).(Command code: 0x0364)

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 100 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: