Panasonic S-ics страница 59 Скачать руководство пользователя

Страница: 59 / 327

Section 700 - Operation

Chapter 3. System Features

S-ICX-64-700

S-ICX (International) issued April 2002

When the system is in Night mode, call can be directed to ring at one or more extensions or at a hunt

group per the Night ringing assignments.

Inbound calls can be directed to desired normal daytime locations by setting the system into a Day

mode. By having a second day mode (Day 2) alternative call handling is available during day

operation. For instance, during lunch, calls can be directed to an alternative position.

Calls can be directed specific night locations when the system is set to Night mode.

For more information on Day Ringing, see “Day/Night System Mode” on page 35.

Hardware Requirements

•

N/A

Considerations

•

N/A

Day 1/ Day 2/Night Delayed Ringing

Delayed Ringing causes an incoming outside call that is unanswered at a primary extension within a

certain period of time, to ring at a designated extension or extensions. Delayed ringing destinations

can be set for Day 1, Day 2 and Night modes. Exchange Line Delayed Ringing is also available for

hunt group pilot numbers.

Hardware Requirements

•

N/A

Considerations

•

N/A

DDI (DID) Day/Night Ringing

(

Note:

Analog DID is not available in the UK, TX or EX model).

Incoming DDI calls can be set to ring at day destinations when the system is in day mode and ring at

night destinations when the system is in night mode.

Hardware Requirements

•

DDI (DID) Trunk Card

Considerations

•

N/A

DDI (DID) Day/Night Busy/Delayed Ringing

DDI Day/Night Busy/Delayed Ringing causes an incoming DDI call to a busy primary extension to

ring at a designated extension or extensions. DDI Busy/Delayed Ringing also causes an incoming

DDI call that is unanswered at a primary extension within a certain period of time, to ring at a

designated extension or extensions. Separate ring destinations are available for day and night modes.

DDI Busy/Delayed Ringing is also available for hunt group pilot numbers. However, when the

Queuing Timer expires, the call leaves the hunt group and is forwarded to the DDI Busy/Delayed

Ringing destination.

Содержание S-ics








































































































































































































































































































































Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды

Panasonic S-ics, Техническое руководство

Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды