Panasonic S-ics Скачать руководство пользователя

Страница: 67 / 327

Section 700 - Operation

Chapter 3. System Features

S-ICX-64-700

S-ICX (International) issued April 2002

Hardware Requirements

•

N/A

Considerations

•

N/A

Trunk Interface - Loop Start

The VB-44510UK Loop Start interface unit supplies 8 loop start analog exchange line circuits. In

addition, the VB-44510UK Loop Start interface unit may alternatively be used to connect to loop start

exchange lines.

Hardware Requirements

•

VB-44510UK Loop Start Card

Considerations

•

N/A

Trunk Ringing Types

Description

Several types of Exchange Line ringing are available for the System including the following:

•

Direct Dial Inward (DDI) Ringing

•

Direct Line (DL) Ringing

•

Direct Inward System Access (DISA) Ringing

•

Multiple Ringing

These ringing types may be used in any combination in the System.

DDI Ringing

DDI Ringing allows calls on a common Exchange Line to be directed to ring to a specific extension or

group of extensions, etc. based upon the final digits dialled. These final digits are received from the

DDI exchange line and compared to a DDI Table that determines where the calls should ring.

Depending on the assignments in the DDI Table, names or exchange line numbers are displayed.

(Names can be up to 10 digits long.)

DDI Ringing can be very useful by sending calls directly to a specific extension, hunt group, etc.

based upon the number dialled. Since a relatively small number of exchange lines handle the DDI

calls, this can be more cost efficient than DL exchange lines or attendant group answering and

transfer. (DDI may send a call to a group using the Virtual Extension feature.) DDI Busy/Delayed

Ringing is also available with DDI Ringing. (See “DDI (DID) Day/Night Busy/Delayed Ringing” on

page 59.)

For more information on DDI Exchange Line Exchange Line Interface, see “Trunk Interface - DDI

(Not Available on UK Model)” on page 66.

Hardware Requirements

•

N/A

Содержание S-ics








































































































































































































































































































































Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды

Panasonic S-ics, Техническое руководство

Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды