Panasonic S-ics Скачать руководство пользователя

Страница: 76 / 327

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 3. System Features

Section 700 - Operation

• Pressing the FL/R key cancels the VM/TRF and returns intercom dial tone to the user.

When the VM/TRF is cancelled, the incoming call is still connected but is on hold.

• If a valid key (Exchange Line key or second DSS key, for example) is pressed, the

VM/TRF is cancelled and the operation invoked by the key is performed.

• If an invalid key (

REDIAL

, for example) is pressed, the VM/TRF is cancelled, and the

user receives busy tone.

• Once VM/TRF is pressed, the user can dial up to 10 digits before completing the transfer.

•

If a user begins to perform the voice mail transfer and the extension cannot hold a call (one call is

already on non-appearance hold, for example), the system will keep the call in the talk state and

will not allow the voice mail transfer to be initiated.

•

If the VM/TRF key stores a number other than a voice mail extension number, the system does

not send DSS/BLF information or the extension number that is dialled after pressing VM/TRF.

Voice over IP Trunk Lines

Version 6.2 and later

Description

A VoIP (Voice over Internet Protocol) Trunk (exchange) line provides up to 16 voice channels over

LAN/WAN lines.
The 8-channel VoIP-TRK/8 (Voice over IP Trunk) card is equipped with one CODEC/8 voice

processing unit. One additional CODEC/8 unit (VB-445801) can be mounted on the card to provide

16 voice channels.
For more information, see

562 - VoIP-TRK Refererence

for ICX and S-ICX.

Hardware Requirements

•

VoIP-TRK card (VB-44580)

•

CODEC/8 unit (optional)

•

LAN/WAN network with sufficient bandwidth

Considerations

•

See

Section 562 - VoIP-TRK Refererence

for ICX and S-ICX.

Содержание S-ics








































































































































































































































































































































Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды

Panasonic S-ics, Техническое руководство

Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды