Panasonic S-ics Скачать руководство пользователя

Страница: 30 / 327

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 3. System Features

Section 700 - Operation

Centrex/PBX Compatibility

Description

Centrex/PBX Compatibility allows the System to be connected behind centrex or PBX lines.
When connected behind a PBX or Centrex,

Automatic Route Selection (ARS) and

Toll Restriction

Service

(

TRS

)

(Call Barring)

must

be used to restrict calls.

The System also supports transmission of a flash signal over the centrex or PBX link.

Hardware Requirements

•

N/A

Considerations

•

N/A

Class of Service

Description

A Class of Service (COS) allows or restricts access to a group of features or functions. For instance,

an Extension COS may allow Call Forwarding features. In the System, both extensions and exchange

lines use classes of service.
The System supports the following COSs for exchange lines and extensions:

•

COS - Exchange Line/Tie

•

COS - Ext/Ext Restriction

•

COS - Extension Feature

•

COS - Exchange Line to Exchange Line Restriction

Class of Service - Trunk/Tie

Tie/Trunk COS allows or restricts access to various features. Each trunk is assigned to one of 16

exchange line classes of service (

The following table shows the features that can be enabled/disabled for each exchange line COS.

Table 4.

Exchange Line COS

Number

Feature

Intercom Ringing Tone (Exchange Line or intercom ring tone)

Dial Tone to Tie Lines (Enable/Disable)

Forced Recover on Fast-Busy Tone (Send fast busy or disconnect line)

DDI Dialled Number Conversion Table (DDI/CLI Table A or B)

Paging on DISA/Tie-Line Call (Allow/Restrict)

DISA Security Code Verification

Network Flash Forwarding

Network Flash Receive

Содержание S-ics








































































































































































































































































































































Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды

Panasonic S-ics, Техническое руководство

Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды