Panasonic S-ics страница 239 Скачать руководство пользователя

Страница: 239 / 327

Section 700 - Operation

Chapter 6. DSLT Features

S-ICX-64-700

S-ICX (International) issued April 2002

239

•

2 extension and 2 trunk lines

•

1 extension and 3 trunk lines

When the optional 8-party conference card is installed, the System supports any combination of

conference calls, except all outside lines.

Operation

See

Section 750 - Key Phone User Guide

for operating instructions.

Hardware Requirements

•

A Conference Card (VB-44120) must be installed in the System in order to conference more than

four parties.

Considerations

•

If all the internal parties hang up, the conference call will be disconnected. If the internal party

remains in the conversation, the conference call remains in progress.

•

When three or four parties are conferenced, a built-in 4-party conference circuit is used. If no

4-party conference circuit is available, a conference cannot be established.

•

When a fifth party is added, the conference is moved to a conference circuit on the 8-party

conference card. If an 8-party conference circuit is not available, a fifth party cannot be added to

a conference.

•

Once an 8-party conference circuit is used, it continues to be used as long as the conference

continues.

•

An 8-party conference card supports up to four 8-party conference circuits. However, the card

must be placed in cabinet slots 1, 5, or 9 to support more than one 8-party conference circuit (and

jumpered accordingly).

•

During a conference call hold, the held conference members cannot use the HOLD key. Pressing

the key has no effect.

•

Conference Hold is an Exclusive Hold (only the conference originator can retrieve the

conference).

•

Conference Hold cannot be transferred.

Do-Not-Disturb

Description

You can make an extension unavailable by activating the Do-Not-Disturb (DND) feature. When DND

is activated, calls to that extension receive busy tone.

You can set or cancel DND from either your extension or from an alternate extension.

Содержание S-ics








































































































































































































































































































































Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды

Panasonic S-ics, Техническое руководство

Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды