Panasonic S-ics Скачать руководство пользователя

Страница: 81 / 327

Section 700 - Operation

Chapter 4. User Maintenance

S-ICX-64-700

S-ICX (International) issued April 2002

Hardware Requirements

•

N/A

Considerations

•

N/A

Set Call Forward Busy Destination Extension

Description

You can assign a Call Forward Busy Destination Extension for each extension. This is typically used

for forwarding calls to voice mail.

Operation

To set a Call Forward Busy Destination Extension using either a large-display or

small-display phone:

11. To set additional Absence Messages, press the volume up

or down key or press the

HOLD

key to move to the desired

Absence Message.

Desired Absence Message displays

12. Repeat steps 7-11 until all Absence Messages are entered.

13. Press the

MEMORY

key to exit the entry mode.

Enter Msg #

displays

14. To return to the top menu level (

), press the

PROG

key.

OR...

To exit the User Maintenance mode, press the

ON/OFF

key.

81-

User MAINT

displays

OR...

ON/OFF

LED goes off

Action

Result

1. If not already in User Maintenance mode, enter User Main-

tenance mode. (See “To enter User Maintenance mode:” on
page 79.)

81-

User MAINT

displays

2. At the

level, enter

3. Press the

HOLD

key.

8109-

TRF of CFWD

displays

4. Enter

5. Press the

HOLD

key.

CFWD-Busy EXT #

displays

6. Dial the extension number.

7. Press the

HOLD

key.

Enter CODE

displays

8. Enter the destination extension.

9. Press the

HOLD

key to store the entry.

Next extension number displays

Action

Result

Содержание S-ics








































































































































































































































































































































Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды

Panasonic S-ics, Техническое руководство

Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды