Panasonic S-ics Скачать руководство пользователя

Страница: 92 / 327

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 4. User Maintenance

Section 700 - Operation

Table 12. Mode Schedule Patterns - addresses & values

4. Press the

HOLD

key.

Mode Schedule

displays

5. Press the

HOLD

key.

000

:HHMM

PTN 1-1 Start T

displays

6. Enter

the start time in hours (two characters) and minutes

(two characters) for the Pattern 1 - first

mode.

Note:

To clear an entry or existing data, press the FL/R key.

7. Press the

HOLD

key.

001

PTN 1-1 Mode

displays

8. Enter the desired mode for Pattern 1 - first (

- None,

Day 1,

- Day 2,

- Night,

- Night (1),

- Night (2)).

Note:

To clear an entry or existing data, press the FL/R key.

9. Press the

HOLD

key to store the entry.

Next pattern mode displays

10. To set additional mode schedules, press the volume up or

down key or press the

HOLD

key to move to the desired

mode.

Desired pattern mode displays

11. Repeat steps 6-10 until all patterns and modes are set.

(There are 3 total patterns with 5 start time/modes each.)

Note:

Entry Positions are listed in Table 12 on page 92.

12. Press the MEMORY key to exit the entry mode.

Mode Schedule

displays

13. To return to the top menu level (

), press the

PROG

key.

OR...

To exit the User Maintenance mode, press the

ON/OFF

key.

81-

User MAINT

displays

OR...

ON/OFF

LED goes off

FF8 1 07 0 (00-29) Hold (MMDD or HHMM or 0-5) Hold

-- VALUES --

(MMDD, HHMM, or 0-5)

-- ADDRESS NOs. (00-29) --

MODES

1st MODE

2nd MODE

3rd MODE

4th MODE

5th MODE

Pattern 1

Start Time
(HHMM)

Mode (0-5):

0=None
1=Day 1

2=Day 2

3=Night
4=Night (1)

5=Night (2)

Action

Result

Содержание S-ics








































































































































































































































































































































Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды

Panasonic S-ics, Техническое руководство

Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды