Panasonic S-ics Скачать руководство пользователя

Страница: 41 / 327

Section 700 - Operation

Chapter 3. System Features

S-ICX-64-700

S-ICX (International) issued April 2002

•

Up to 2 Doorphones can be connected to a Doorphone Adaptor and utilize the same exchange

line.

•

The Door Opener can be set to open for 15 seconds, 30 seconds, or one minute.

•

While the Door Opener is functioning, a call from another Doorphone on the same Doorphone

Adaptor cannot be answered.

Considerations

•

The exchange line connected to the Doorphone Adaptor must be set to dial pulse (DP).

Doorphone Sensor

The sensor is a device that detects when a circuit is opened or closed. Sensors can be used to detect

events such as the opening of windows or doors. When the sensor is tripped, a tone sounds at a

designated extension. Sensors are not sold by Panasonic; however, they can be purchased separately

from an electronics dealer.

Hardware Requirements

•

The sensor is attached to the Doorphone Adaptor (VB-3473UK).

•

Exchange Lines connected to the Doorphone Adaptor signal the designated extension when the

sensor is tripped.

Considerations

•

The exchange line connected to the sensor must be a dial-pulse (DP) exchange line.

Extension Interface

The System supports a full array of extension devices including the following:

•

Panasonic’s proprietary key telephones

•

Standard analog devices

•

Dial Pulse (DP) / Dual Tone Multifrequency (DTMF) Single Line Telephone (SLT)

•

Integrated Services Digital Network (ISDN) - Basic Rate Interface (BRI) S-point devices

•

ISDN-Primary Rate Interface (PRI) S-point devices

Digital Telephones

The S-ICX supports a variety of Panasonic proprietary Digital Key Telephones. These models

include:

Interface Card Type

VB-44660 APEC/8

Åñ

VB-44660 APEC/8

Åñ

VB-44610  DEC/8
VB-44612  DEC/16
VB-44613  DEC/24

Model of Telephones connected

via interface card

A series telephone

VA-30920

VA-12020

VA-12022

SBS telephones

VB-9211

VB-9211DS

VB-9411

VB-9411DS

VB-9411ADS

DBS/ICX telephones

VB-3411

VB-3411DS

VB-3411LDS

VB-3611D

VB-D411

VB-D411DS

VB-D411DSV

VB-D411LDS

VB-D611D

VB-D611DS

Содержание S-ics








































































































































































































































































































































Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды

Panasonic S-ics, Техническое руководство

Результаты поиска

Содержание S-ics

Отзывы:

Похожие инструкции для S-ics

Бренды по названию

Популярные бренды