Panasonic S-ics Скачать руководство пользователя страница 82

Страница: 82 / 327

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 4. User Maintenance

Section 700 - Operation

Hardware Requirements

•

N/A

Considerations

•

N/A

Set Call Forward ID Codes for Voice Mail

Description

(For a description of Call Forward ID codes for Voice Mail, see “Call Forward ID Code for Voice

Mail” on page 72.)

Voice Mail Call-Forward ID codes are used by voice mail systems to identify the correct mail box for

storing messages. The actual entry needed will vary by voice mail systems and configuration. Often

the entry is the extension number.

Operation

To set the Call Forward ID code:

10. To set Call Forward Busy destinations for additional

extensions, press the volume up and down key or press the

HOLD

key to move to the desired Extension.

11. Repeat steps 9-11 until all extension are entered.

12. Press the MEMORY key to exit the entry mode.

13. To return to the top menu level (

), press the

PROG

key.

OR...

To exit the User Maintenance mode, press the

ON/OFF

key.

81-

User MAINT

displays

OR...

ON/OFF

LED goes off

Action

Result

1. If not already in User Maintenance mode, enter User Main-

tenance mode. (See “To enter User Maintenance mode:” on
page 79.)

81-

User MAINT

displays

2. At the

level, enter

3. Press the

HOLD

key.

8105-

C.FWD ID Code

displays

4. Press the

HOLD

key.

CF ID-EXT Number

displays

5. Dial the extension number.

6. Press the

HOLD

key.

CF-ID EXT

XXX

displays (where

XXX = extension number)

Action

Result

Содержание S-ics








































































































































































































































































































































Результаты поиска

Содержание S-ics

Отзывы:

Бренды по названию

Популярные бренды

Panasonic S-ics, Техническое руководство

Результаты поиска

Содержание S-ics

Отзывы:

Бренды по названию

Популярные бренды