Panasonic MADLN05NL Скачать руководство пользователя

Страница: 45 / 115

No. SX-DSV03224-42-

R6.0

Motion Control Business Unit, Panasonic Corporation

7-3 RTEX connectors X2A X2B

For connection, use RJ45 connector

[X2A] RX connector

Name

Symbol

pin no.

Description

Unused

Connect to pin 1 on TX connector of sending side node.

Unused

Connect to pin 2 on TX connector of sending side node.

Network input +

RX+

Connect to pin 3 on TX connector of sending side node.

Unused

Connect to pin 4 on TX connector of sending side node.

Unused

Connect to pin 5 on TX connector of sending side node.

Network input -

RX-

Connect to pin 6 on TX connector of sending side node.

Unused

Connect to pin 7 on TX connector of sending side node.

Unused

Connect to pin 8 on TX connector of sending side node.

Frame ground

Shell

Connect to shield of cable.

[X2B] TX connector

Name

Symbol

pin no.

Description

Unused

Connect to pin 1 on RX connector of receiving side node.

Unused

Connect to pin 2 on RX connector of receiving side node.

Network

TX+

Connect to pin 3 on RX connector of receiving side node.

Unused

Connect to pin 4 on RX connector of receiving side node.

Unused

Connect to pin 5 on RX connector of receiving side node.

Network output -

TX-

Connect to pin 6 on RX connector of receiving side node.

Unused

Connect to pin 7 on RX connector of receiving side node.

Unused

Connect to pin 8 on RX connector of receiving side node.

Frame ground

Shell

Connect to shield of cable.

* Be sure to use shielded twisted pair (STP) compatible with 5e of TIA/EIA-568 or higher category

7-4 Safety function connector X3

This connection is for functional safety.

This connector is compatible with multifunction type only.

Name

Symbol

pin No

Description

Input/output

signal interface

Reserved

−

・

Do not connect anything to this connector.

−

Safety input 1

SF1-

2 channel inputs with independent circuit
to cut off the drive signal to the power module
in the servo driver.

i-1

SF1+

Safety input 2

SF2-

SF2+

EDM output

EDM-

・

It is monitor output for monitoring malfunctions of

the safety function.

o-1

EDM+

Frame ground

shell

・

Internally connected to the earth terminal.

Note 1)

The signal ground GND is connected with the control circuit ground connected with the connector X3 .

Note 2) “Safety Integrity Level 3(SIL3)”, “Performance level e (PL e)” and “DCavg Medium” are accomplished with

diagnosis of “EDM output” (maximum interval time is 3 months). Without diagnosis of “EDM output”, the safety Integrity Level is
2 (SIL2), Performance level d (PL d) and “DCavg Low”.

Содержание MADLN05NL




















































































































Результаты поиска

Содержание MADLN05NL

Отзывы:

Похожие инструкции для MADLN05NL

Бренды по названию

Популярные бренды

Panasonic MADLN05NL, Руководство пользователя

Результаты поиска

Содержание MADLN05NL

Отзывы:

Похожие инструкции для MADLN05NL

Бренды по названию

Популярные бренды