Panasonic MADLN05NL Скачать руководство пользователя

Страница: 46 / 115

No. SX-DSV03224-43-

R6.0

Motion Control Business Unit, Panasonic Corporation

7-5 I/O connector X4

Input signals

Name

Symbol Pin No.

Description

Input/output

signal interface

General input common

SI-COM

・

Connect to the + terminal or - terminal of an external DC power supply

(12 to 24 V)

・

Use 12 V±5% to 24 V±5% for power supply.

・

Insulation is needed against the primary side power supply.

Do not connect with the same power supply.
* primary power supply : Power supply for Motor brake

―

Control input 1

SI1

• Allocate functions by parameters.

For details, refer to "Technical Reference -Functional

Specification-"

• Range of available functions is limited.

For example, external latch input EXT1 can be allocated only to SI5,
EXT2 to SI6 and EXT3 to SI7.

i-1

Control input 2

SI2

Control input 3

SI3

Control input 4

SI4

Control input 5

SI5

Control input 6

SI6

Control input 7

SI7

Control input 8

SI8

Output signals

Name

Symbol Pin No.

Description

Input/output

signal interface

Control

output 1

SO1+

SO1-

1
2

• Allocate functions by parameters.

For details, refer to "Technical Reference -Functional

Specification-"

o-1

Control

output 2

SO2+

SO2-

25
26

Control

output 3

SO3+

SO3-

3
4

Feedback scale output signal / Position comparison output signal

Name

Symbol Pin No.

Description

Input/output

signal interface

A-phase output

Position comparison

Output 1

OA+/

OCMP1+

• Differential output of divided feedback scale signal or external scale

signal

(A – Bphase). (RS422 compatible)



The division ratio can be set by the parameters.

• The ground of line driver for the output circuit is connected to the signal

ground (GND) and kept non-insulated.

• Maximum output frequency is 4 Mpps (after multiplied by 4).



It can be used as position compare output by parameter setting.

For details, refer to "Technical

Reference

-Functional Specification-"



This differential signal should be received by a line receiver

(AM26C32or equivalent). Connect a terminating resistor (approx.
330 Ω) between the line receiver inputs.



For wiring, use shielded twisted pair cable, please connect shielded wire

to connector shell.

Do-1

OA-/

OCMP1-

B-phase output/

Position comparison

Output 2

OB+/

OCMP2+

OB-/

OCMP2-

Position comparison

Output 3

OCMP3+

OCMP3-

Signal ground

GND

•Signal ground
• Be sure to connect the line receiver ground to this terminal.

―

Содержание MADLN05NL




















































































































Результаты поиска

Содержание MADLN05NL

Отзывы:

Похожие инструкции для MADLN05NL

Бренды по названию

Популярные бренды

Panasonic MADLN05NL, Руководство пользователя

Результаты поиска

Содержание MADLN05NL

Отзывы:

Похожие инструкции для MADLN05NL

Бренды по названию

Популярные бренды