Oki MB760 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 390

background image

45641001TH Rev.1

4-16 /

Oki Data CONFIDENTIAL

4.4.3

Background adjustment (Color Mode)

The adjustment level of background center value is adjusted. The control value of background
adjustment button is automatically adjusted to the same level as the adjusted center value.

For example, when the control value of background adjustment key ranges from 0 to 6, the

background center value (-2 to +2) is used to be the range from 6 to 14 accordingly.

Before adjustment

After adjustment

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

+2

+1

0

-1

-2

-1

-2

+2

+1

0

Fig 6-2

<Adjustment Mode (05)>

Code

Original mode

Remarks

8309

Text/Photo

The smaller the value is, the background becomes lighter.
Acceptable values: 0 to 255 (Default: 128)

8310

Text

8311

Photo

8370

Custom mode

<Procedure>

(1) While pressing [0] and [5] simultaneously, turn the power ON.

(2) Key in the codes and press the [START] button.

(3) Key in the adjustment values. Acceptable values: 0 to 255. (To correct the value once keyed

in, press the [CLEAR] button.)

(4) Press the [OK] or [INTERRUPT] button to store the value in memory.

→

The equipment goes back to the ready state.

(5) Let the equipment restart and perform the scanning job.

(6) If the desired image has not been attained, repeat step (1) to (5).

4.4.4

Background adjustment (Black/Grayscale)

The density of background can be adjusted as follows.

<Adjustment Mode (05)>

Code

Color mode

Original mode

Remarks

7436

Black

Text/Photo

The smaller the value is, the background

becomes lighter.

Acceptable values: 0 to 255 (Default: 128)

7437

Text

7438

Photo

7441

Custom mode

7439

Grayscale

−

<Procedure>

The procedure is the same as that of



P. 4-15 “4.4.2 Density adjustment”.

«
...
73
74
75
76
77
...
»

Содержание MB760







































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MB760

Бренд: Xerox Страницы: 34

Бренд: QMS Страницы: 311

Бренд: Partner Страницы: 9

Бренд: BIO RAD Страницы: 61

Бренд: Star Страницы: 82

Бренд: Xerox Страницы: 288

Бренд: UEi Страницы: 4

4250 - WorkCentre - Copier

Бренд: Xerox Страницы: 4

Бренд: Oki Страницы: 8

Бренд: Oce Страницы: 76

Бренд: DURACARD Страницы: 31

Бренд: Star Страницы: 2

Бренд: Infinite Peripherals Страницы: 27

Бренд: Konica Minolta Страницы: 150

Бренд: MF DIGITAL Страницы: 9

Бренд: Sunso Страницы: 27

Бренд: DataCard Страницы: 24

Бренд: SATO Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды