Oki MB760 Скачать руководство пользователя | Manualshive

Страница: 24 / 390

background image

45641001TH Rev.1

3-1 /

Oki Data CONFIDENTIAL

3.

seLF-DIaGNOsTIC mODe

3.1 Overview

[a] starting each mode

To enter the desired mode, turn the power ON while pressing two digital keys designated to

each mode (e.g. [0] and [5]) simultaneously. Hold the two keys until the [PRINT DATA] lamp is lit.

On the authentication screen displayed after starting up each mode, enter the service password,
and then press [OK]. The password is not set by default.

Refer to “Appendix” for the codes in Test mode (03), Test print mode (04), Adjustment mode (05),
and Setting mode (08).

[B] exiting from each mode

Shut down the equipment. When the power should be turned OFF, be sure to shut down the
equipment by pressing the [ON/OFF] button for a few seconds.

[C] List of modes

Mode

For start

Contents

For exit

Display

Control panel
check mode

[0] + [1] +

[POWER]

All LEDs on the control panel are lit, and all
the LCD pixels blink.

[POWER]

OFF/ON

-

Test mode

[0] + [3] +

[POWER]

Checks the status of input/output signals.

[POWER]

OFF/ON

100% C
TEST MODE

Test print
mode

[0] + [4] +

[POWER]

Outputs the test patterns.

[POWER]

OFF/ON

100% P A4
TEST PRINT

Adjustment

mode

[0] + [5] +

[POWER]

Adjusts various items.

[POWER]

OFF/ON

100% A A4
TEST MODE

Setting mode

[0] + [8] +
[POWER]

Sets various items.

[POWER]

OFF/ON

100% D
TEST MODE

Maintenance
mode

[6]+[8]+
[POWER]

Maintains the scanner unit (SU) and printer
unit (PU)

[POWER]

OFF/ON

-

Assist mode

[3]+[C]+

[POWER]

Clears error flags or SRAM, or safely deletes

data in the HDD or SRAM to support the

replacement of the SYS board, SRAM or

HDD.

[POWER]

OFF/ON

-

HDD assist
mode

[4]+[CLEAR]+
[POWER]

Assists the ADI-HDD by checking the type

of the mounted HDD, reverting the HDD to a

factory default or removing keys.

[POWER]

OFF/ON

-

File system
recovery mode

[5] + [C] +

[POWER]

Checks, recovers or initializes the file system

(HDD).

[POWER]

OFF/ON

-

SRAM clear
mode

[6]+[CLEAR]+
[POWER]

Recovers the equipment from particular
errors such as F800 or F900.

[POWER]

OFF/ON

-

List print mode

[9] + [START]

+ [POWER]

Prints various lists or outputs them in a CSV

format.

[POWER]

OFF/ON

100% L A4
LIST PRINT

Firmware
update mode

[4] + [9] +

[POWER]

Performs firmware update with USB device.

[POWER]

OFF/ON

-

[8] + [9] +
[POWER]

Performs firmware update with download jig.

[POWER]

OFF/ON

-

Password
reset mode

[4] + [8] + [9]
+ [POWER]

Resets the administrator password and
service password.

[POWER]

OFF/ON

-

SRAM data
cloning mode

[5] + [9]

+ [POWER]

Backs up the SRAM data to USB device.

[POWER]

OFF/ON

-

«
...
22
23
24
25
26
...
»

Содержание MB760







































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MB760

Бренд: F+D Feinwerk- und Drucktechnik Страницы: 41

Бренд: Lanier Страницы: 6

Бренд: Canon Страницы: 2

imageRUNNER C3480

Бренд: Canon Страницы: 92

Бренд: Oki Страницы: 328

Бренд: Ricoh Страницы: 682

Бренд: BIXOLON Страницы: 29

Бренд: Rena Страницы: 59

Бренд: Custom Audio Electronics Страницы: 88

Бренд: HandTop Страницы: 97

Digital Minilab Frontier LP5700R

Бренд: FujiFilm Страницы: 2

Бренд: Lexmark Страницы: 2

workforce wf-2630

Бренд: Epson Страницы: 256

WorkForce Pro WP-4595 DNF

Бренд: Epson Страницы: 2

WorkForce WF-2540

Бренд: Epson Страницы: 283

WorkForce ST-C4100

Бренд: Epson Страницы: 333

WorkForce WF-2540

Бренд: Epson Страницы: 2

Бренд: Ice Страницы: 133

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды