manualshive.com logo in svg

Oki MB760, Руководство по обслуживанию

Скачайте бесплатное руководство пользователя и таблицу безопасности материалов для Oki MB760 с нашего веб-сайта. Получите всю необходимую информацию о продукте, включая инструкции по эксплуатации и рекомендации по безопасности. Наслаждайтесь безопасным и эффективным использованием вашего устройства Oki MB760.

Поделиться
Скачать
background image

45641001TH  Rev.1 

8-26 / 

Oki  Data  CONFIDENTIAL

8.5.1 

FAX unit firmware (GD-1340)

Important:

•  Before updating the FAX firmware, make sure to print out the current Function list for 

maintenance, Function list (ADMIN), Address book list and Group number information. 

In case the updating is failed and the registered information of the users is lost for some 

reason, re-register the user information referring to the lists and recover it.

•  Confirm the following items before turning OFF the power of the equipment. Turning OFF the 

power may clear the data below.

-  Confirm that the “MEMORY RX” LED is OFF and there are no memory reception data.

-  Press the [JOB STATUS] button to display the screen and then confirm that there are no 

memory transmission data.

-  Print the “Mailbox/Relay box report” and then confirm that there are no F code data.

[a]   Update Procedure

(1)  Install the ROM to the download jig (K-PWA-DLM-320).

 

Make sure the direction is correct.

(2)  Press the [ON/OFF] button to shut down the equipment.

(3)  Take off the right side cover.
 

 P. 6-1 “6.1.1 Right side cover”

(4)  Connect the download jig [1] with the jig connector [2] on the FAX board.

Fig.8-18

(5)  Press the [ON/OFF] button while simultaneously holding down the [0] and [8] buttons.
 

Updating starts automatically and the LED on the download jig lights.

(6)  After the update is completed properly, the LED on the download jig blinks.
 

The LED starts blinking approx. 30 sec. after the update starts. It is assumed that the 

update has failed if it does not start blinking even though 1 min. has passed. In this 

case, shut down the equipment and check the following items. Then clear the problems 

and restart updating from the beginning.

•  Is the download jig connected properly?
•  Is the ROM installed to the download jig properly?
•  Is the updating data written on the ROM of the download jig properly?
•  Do the download jig and the equipment operate properly?

Содержание MB760







































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MB760

Samsung SCX-3405FW Manual Del Usuario preview
SCX-3405FW
Бренд: Samsung Страницы: 347
Samsung SCX 6555N - MultiXpress Mono Multifunction Manual Del Usuario preview
SCX 6555N - MultiXpress Mono Multifunction
Бренд: Samsung Страницы: 180
Samsung SCX-4300 - SCX 4300 B/W Laser License Agreement preview
SCX-4300 - SCX 4300 B/W Laser
Бренд: Samsung Страницы: 18
Samsung SCX-4521FG - B/W Laser - All-in-One User Manual preview
SCX-4521FG - B/W Laser - All-in-One
Бренд: Samsung Страницы: 215
Samsung SCX 6320F - B/W Laser - All-in-One User Manual preview
SCX 6320F - B/W Laser - All-in-One
Бренд: Samsung Страницы: 332
Samsung SCX 4828FN - Laser Multi-Function Printer User Manual preview
SCX 4828FN - Laser Multi-Function Printer
Бренд: Samsung Страницы: 248
Samsung SCX 4725FN - B/W Laser - All-in-One User Manual preview
SCX 4725FN - B/W Laser - All-in-One
Бренд: Samsung Страницы: 253
Samsung ML 2851ND - B/W Laser Printer User Manual preview
ML 2851ND - B/W Laser Printer
Бренд: Samsung Страницы: 179
Samsung ML 2510 - B/W Laser Printer Manual Del Usuario preview
ML 2510 - B/W Laser Printer
Бренд: Samsung Страницы: 84
Samsung ML 1740 - B/W Laser Printer Manual Del Usuario preview
ML 1740 - B/W Laser Printer
Бренд: Samsung Страницы: 152
Samsung ML 1630 - B/W Laser Printer User Manual preview
ML 1630 - B/W Laser Printer
Бренд: Samsung Страницы: 142
Samsung ML 1630 - B/W Laser Printer Manual Del Usuario preview
ML 1630 - B/W Laser Printer
Бренд: Samsung Страницы: 82
Samsung SL-M2875FD Installation Manual preview
SL-M2875FD
Бренд: Samsung Страницы: 2
Samsung M337 User Manual preview
M337
Бренд: Samsung Страницы: 384
Samsung Lazett Combo SCX-4216F Service Manual preview
Lazett Combo SCX-4216F
Бренд: Samsung Страницы: 135
Samsung CLX-6260FD Manual Del Usuario preview
CLX-6260FD
Бренд: Samsung Страницы: 414
Samsung SCX 6555N - MultiXpress Mono Multifunction Administrator'S Manual preview
SCX 6555N - MultiXpress Mono Multifunction
Бренд: Samsung Страницы: 112
Samsung scx-4100 series Quick Install Manual preview
scx-4100 series
Бренд: Samsung Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды