Oki MB760 Скачать руководство пользователя страница 257 | Manualshive

Страница: 257 / 390

background image

45641001TH Rev.1

8-7 /

Oki Data CONFIDENTIAL

Notes:

• The display of items on this screen varies depending on the types of data written

on the USB device.

Each item is displayed only when each data file is written on the USB device in

the following conditions.

Item

Condition

1. SYSTEM FIRMWARE

(OS Data)

O290SF0Wxxxx.tar is written. (xxxx is version.)

2. ENGINE FIRMWARE

H291PUPWW.xxxx is written. (xxxx is version.)

3. SCANNER FIRMWARE

H282SUPWW.xxxx is written. (xxxx is version.)

4. SYSTEM SOFTWARE

(HD Data)

O290HD0Wxxxx.tar is written. (xxxx is version.)

• If the USB device is not recognized properly, “USB device Not detected” message

is displayed. In this case, disconnect the USB device and connect again within
3 minutes, or shut down the equipment and connect the device properly. Then

repeat the procedure from (4).

• If any of the error messages below is displayed, confirm if the data file in the USB

device is correct.

Then repeat the procedure from (4).

Error

number

Error message

Cause

01

Error Loadmodule

Module loading failed.

02

Machine Model Get Error

Model information was
not downloaded.

03

Copy Data with valid signature in USB Storage Checking of data file

failed.

04

Other models ROMDATA TXXXXXXXX
* The version name comes at “xxxx.xxx.x”.

Master data of other
model are stored.

05

Copy Signature File in USB Storage

Data files are not
stored in the USB
device.

06

Patch and Normal package in one folder
of USB Storage

When both the system

and patch update
packages are in the
USB device

(6) Select the item with the digital keys.

“*” is displayed next to the selected item. Display or delete the “*” by pressing the

number of the item.

Item

Remarks

1. SYSTEM FIRMWARE(OS Data)

Updating System firmware

2. ENGINE FIRMWARE

Updating PU firmware

3. SCANNER FIRMWARE

Updating SU firmware

4. SYSTEM SOFTWARE (HD Data)

Updating System software

«
...
255
256
257
258
259
...
»

Содержание MB760







































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MB760

Бренд: Oki Страницы: 268

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 202

Бренд: Oki Страницы: 201

Бренд: Oki Страницы: 103

Бренд: Oki Страницы: 256

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 63

Бренд: Oki Страницы: 28

Бренд: Oki Страницы: 616

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 138

Microline 320 Turbo D1

Бренд: Oki Страницы: 2

ML320 Epson/IBM

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды