Oki MB760 Скачать руководство пользователя | Manualshive

Страница: 152 / 390

background image

45641001TH Rev.1

5-69 /

Oki Data CONFIDENTIAL

[2]

RFC related error

[2500] HOsT Name error (RFC: 500) / Destination mail address error (RFC: 500) / Terminal

mail address error (RFC: 500)

[2501] HOsT Name error (RFC: 501) / Destination mail address error (RFC: 501) / Terminal

mail address error (RFC: 501)

Check if the Terminal mail address and Destination mail address are correct.
Check if the mail server is operating properly.

Turn the power OFF and then back ON. Perform the job in error again.

[2503] Destination mail address error (RFC: 503)
[2504] HOsT Name error (RFC: 504)
[2551] Destination mail address error (RFC: 551)

Check if the mail server is operating properly.

Turn the power OFF and then back ON. Perform the job in error again.
If the error still occurs, replace the SYS board.

[2550] Destination mail address error (RFC: 550)

Check the state of the mail box in the mail server.

[2552] Terminal/Destination mail address error (RFC: 552)

Confirm the size on the mail server.
Transmit again in text mode or with lower resolution or divide the document and transmit again.

If the error still occurs, turn the power OFF and then back ON. Perform the job in error again.

[2553] Destination mail address error (RFC: 553)

Check if there is an illegal character in the mail box in the mail server.

[3]

electronic Filing related error

[2B11] JOB status abnormality
[2B20] File library function error
[2B30] Insufficient disk space in BOX partition
[2BC0] Fatal failure occurred

Erase some data in the Electronic Filing or the shared folder and perform the job in error

again (in case of [2B30]).
Ask the administrator if e-Filing has been disabled. (In case of [2CC1])

Turn the power OFF and then back ON. Perform the job in error again.
Check if there are no other running jobs and perform the HDD formatting ([5] + [C] + [POWER]

ON

→

[3]

→

[1]).

If the recovery is still not completed, replace the SYS board.

[2B31] status of specified electronic Filing or folder is undefined or being created/deleted

Check if the specified Electronic Filing or folder exists. (If no, this error would not occur.)

Delete the specified Electronic Filing or folder.

Perform the job in error again.

[2B50] Image library error
[2B90] Insufficient memory capacity

Turn the power OFF and then back ON. Perform the job in error again.
If the error still occurs, replace the main memory.
Delete the job in progress or being set or in the HOLD/PRIVATE/PROOF/INVALID, and retry
the job in error.

«
...
150
151
152
153
154
...
»

Содержание MB760







































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MB760

Бренд: EASYPRINT Страницы: 37

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 3

Бренд: Xerox Страницы: 8

Versant 3100 Press

Бренд: Xerox Страницы: 45

Бренд: SATO Страницы: 2

Бренд: KIP Страницы: 103

WorkCentre Pro 32

Бренд: Xerox Страницы: 14

Perfecta 2400STP

Бренд: Variquest Страницы: 12

Бренд: Ascend Страницы: 6

IM C6000 Series

Бренд: Ricoh Страницы: 2

bizhub PRO C65hc

Бренд: Konica Minolta Страницы: 24

Бренд: Ricoh Страницы: 88

Бренд: Graphic Products Страницы: 28

DocuPrint 4635 IPS Series

Бренд: Xerox Страницы: 16

Бренд: Panasonic Страницы: 5

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды