Oki MB760 Скачать руководство пользователя страница 323

Страница: 323 / 390

45641001TH Rev.1

11-25 /

Oki Data CONFIDENTIAL

05/

Mode

Element

Sub

element

Item

Subitem

Code Sub-

code

Details

Default

value

Acceptable

value

RAM

Contents

Proce-

dure

Setting
Mode

System

Network

Direct SMTP

3810

Communication
setting

0-1

SYS

When an Internet Fax is sent, Direct SMTP communication

is set.
0: Disabled
1: Enabled

When “0: Disabled” is set, an Internet Fax is sent using
an SMTP server. When “1: Enabled” is set, direct SMTP

communication is enabled and an Internet Fax is sent to
MFPs

If “1: Enabled” is set in 08-3810, set “1: Enabled” in 08-
3812 as well.

Setting
Mode

System

Network

Direct SMTP

3811

Image encrypting
at the Direct SMTP

0-1

SYS

When Direct SMTP communication is performed, an

attached image is encrypted.
0: Disabled
1: Enabled

Setting
Mode

System

Network

Internet Fax

3812

Dummy full mode
at transmission

0-1

SYS

When an Internet Fax is sent, the resolution ratio and the

paper size of an attached image are set to the full mode.
0: Disabled
1: Enabled

If “1: Enabled” is set in 08-3810, set “1: Enabled” in 08-
3812 as well.

Setting
mode

System

Scanner

XPS file

3815

Thumbnail addition

0-1

SYS

Thumbnail is added to the XPS file produced by the

Scan function.
0: Not added
1: Only the top page added

Setting
mode

System

Scanner

XPS file

3816

Paper size setting

0-1

SYS

The paper size of the XPS file produced by the Scan

function is set.
0: Scanned image size
1: Standard size

Setting
mode

System

Scanner

PDF file

3817

Version setting

0, 1, 4

SYS The version of PDF file produced by the Scan function is

set.

0: PDF V1.3 1: PDF V1.4 4: PDF V1.7

Setting
mode

System

General

3833

Home directory
function

0-1

SYS Function to store a file in the user’s home directory

0: Disabled
1: Enabled

Setting
mode

System

General

3837

Display switching
for the machine
name shown in the
notification

0-1

SYS The display method of the machine name shown in the

event related notification is switched.
0: IP address
1: NetBIOS name

Setting
mode

System

General

License control

3840

Registration/
deletion

Registers electronic keys for setting related optional

items (e.g. when the equipment is delivered). Returns the

license file having the same ID as that in the one- time
dongle. Displays all the electronic keys stored in a USB

media connected to the equipment in a list.
Displays electronic keys registered in the equipment.

Содержание MB760







































































































































































































































































































































































































Результаты поиска

Содержание MB760

Отзывы:

Похожие инструкции для MB760

Бренды по названию

Популярные бренды

Oki MB760, Руководство по обслуживанию

Результаты поиска

Содержание MB760

Отзывы:

Похожие инструкции для MB760

Бренды по названию

Популярные бренды