Oki MB760 Скачать руководство пользователя страница 379

Страница: 379 / 390

45641001TH Rev.1

11-81 /

Oki Data CONFIDENTIAL

05/

Mode

Element

Sub

element

Item

Subitem

Code Sub-

code

Details

Default

value

Acceptable

value

RAM

Contents

Proce-

dure

Setting
mode

System

Maintenance RDMS

Long interval

polling

9626

Setting of polling at
the end of month

0-1

SYS 0: Invalid

1: Valid

Setting
mode

System

Network

InternetFAX

9627

Sending mail text

of Internet FAX

0-1

SYS 0: Invalid

1: Valid

Setting
mode

System

Network

SMTP

9628

From Name
Creation setting
in SMTP
authentication

0-2

SYS 0: Not edited

1: Account name of From ADevice name

2: LDAP searching

Setting
mode

System

Wireless
LAN

9649

Wireless LAN

setting

1-2

NIC

Sets whether the wireless LAN connection is enabled or

disabled.
1: Enabled
2: Disabled

Setting
mode

System

Network

DHCP

9694

Enabling server’s
IP address

acquired by DHCP

1-2

DNS domain name Option (15) DNS domain name of the
client
1: Enabled
2: Disabled
This value is used only when DHCP is enabled.

Setting
Mode

System

Maintenance General

9700

Service technician
telephone number

32 digits SYS A telephone number can be entered up to 32 digits.

Use the [MONITOR/PAUSE] button to enter a hyphen(-).

Setting
mode

System

User
interface

9702

Automatic
calibration
disclosure level

0-2

SYS Sets the disclosing level of automatic calibration.

0: Service technician
1: Administrator
2: User

Setting
Mode

System

Maintenance General

9703

Error history
display

SYS Displays the latest 20 errors data

Setting
mode

System

Network

Scanning

9709

Default data saving

directory of “Scan

to File”

0-2

SYS

0: Local directory

1: REMOTE 1
2: REMOTE 2

Setting
Mode

System

Maintenance RDMS

General

9710

Remote-controlled
service function

0-2

SYS

0: Valid (Remote-controlled server)
1: Valid (L2)

2: Invalid

Setting
Mode

System

Maintenance RDMS

HTTP

9711

Remote-controlled

service URL

setting

SYS Maximum 256 letters

Setting
Mode

System

Maintenance RDMS

HTTP

9715

Initially-registered

server URL setting

Refer to

contents

SYS Maximum 256 letters

<Default value>
https://device.mfp-
support.com:443/device/firstregist.ashx

Setting
mode

System

Maintenance
(Remote)

RDMS

9718

Short time interval
setting of recovery
from Emergency
Mode

1-48

SYS Sets the time interval to recover from the Emergency

Mode to the Normal Mode. (Unit: Hour)

Содержание MB760







































































































































































































































































































































































































Результаты поиска

Содержание MB760

Отзывы:

Похожие инструкции для MB760

Бренды по названию

Популярные бренды

Oki MB760, Руководство по обслуживанию

Результаты поиска

Содержание MB760

Отзывы:

Похожие инструкции для MB760

Бренды по названию

Популярные бренды