OHAUS DISCOVERY BALANCE Скачать руководство пользователя страница 54

Страница: 54 / 99

CHAPTER 3 REPAIR PROCEDURES

3.2.4 Load Cell Assembly

5.20. Remove Brass Rod and check vertical centering over Temperature Sensor

Tube and around Magnet.

5.21. Tighten screws on yoke, checking again to ensure Ratio Beam remains

centered.

5.22. Re-tighten Threaded Rod.

5.23. Re-install Hanger and Thumb screws, and Brass Rod, and re-check centering.

NOTE:

Repeat the process as necessary to ensure that the Ratio Beam is centered.

6. Re-check that everything is assembled properly.

7. Remove the Brass Rod and Threaded Rod and ensure that the Ratio Beam moves

up and down without binding.

8. When satisfied that the Ratio Beam moves correctly, reinstall the Brass Rod and

Threaded Rod.

9. Install the Hanger with the Brass Fixture and the Thumb Screws from the Service

Toolset. The Brass Fixture is inserted between the Hanger and the frame of the
Load Cell. Use the Brass Brackets from the Service Toolset to position it properly.
Then tighten the Thumb Screws.

10. Double-check that the Ratio Beam is centered. Repeat process as necessary.

NOTE:

The Hanger should be positioned evenly around the Ratio Beam.

The Hanger’s left and right gap areas should be even when it is installed correctly.

Right gap area

Left gap area

Right side
Bracket

Left side
Bracket

Brass
Fixture

Hanger

Figure 3-67. Hanger installed, with Brass Fixture

and Brass Brackets.

Ohaus Corporation www.ohaus.com

3-34

Discovery Balance Service Manual

Содержание DISCOVERY BALANCE




































































































Результаты поиска

Содержание DISCOVERY BALANCE

Отзывы:

Похожие инструкции для DISCOVERY BALANCE

Бренды по названию

Популярные бренды

OHAUS DISCOVERY BALANCE, Руководство по обслуживанию

Результаты поиска

Содержание DISCOVERY BALANCE

Отзывы:

Похожие инструкции для DISCOVERY BALANCE

Бренды по названию

Популярные бренды