OHAUS DISCOVERY BALANCE Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 99

background image

CHAPTER 2 DIAGNOSIS

TABLE 2-2. BALANCE DOES NOT RESPOND TO FRONT PANEL CONTROLS.

SYMPTOM PROBABLE

CAUSE

REMEDY

Balance does not
respond to front panel
controls.

PC board switch or
actuating fingers on top
housing are defective.

Display PC Board is
defective.

Main PC Board is
Defective

Open the balance. (Refer to
Section 3.1.1. Using an
Ohmmeter, measure the
resistance between the pins of
the ON/Zero Off switch. It should
be open. Press the switch
through the top housing and
check that the resistance is zero.
Check each switch in a similar
manner. If continuity is not
present on a particular switch,
replace the affected switch or
actuator.

If the balance fails to turn on and
On/Zero Off switch is OK, the
Display PC Board may be
defective and should be replaced.
->Display PCB Repair &
Replacement 3.1.2

If Balance fails to turn on and
Display PCB has been replaced
then the Main PCB should be
replaced.
->Main PCB Removal &
Replacement 3.1.3

TABLE 2-3. NO DISPLAY OR PARTIAL DISPLAY

SYMPTOM PROBABLE

CAUSE

REMEDY

Display is not on or
partial characters are
displayed.

Display PC Board is
defective.

The Display PC Board is replaced
as a whole assembly. Check
procedures in Table 2-1 first and
verify that other problems do not
exist.

->Display PCB Removal &
Replacement 3.1.2.

Discovery Balance Service Manual

2-3

Ohaus Corporation www.ohaus.com

«
...
15
16
17
18
19
...
»

Содержание DISCOVERY BALANCE




































































































Отзывы:

Нет отзывов

Похожие инструкции для DISCOVERY BALANCE

Бренд: Taylor Страницы: 2

Бренд: V-fitness Страницы: 2

Бренд: G&G Страницы: 18

Бренд: MOB Страницы: 8

Бренд: Yamato Страницы: 8

Бренд: Cardinal Страницы: 12

Бренд: KERN Страницы: 19

Бренд: UFESA Страницы: 36

Бренд: A&D Страницы: 101

Бренд: American Weigh Страницы: 6

Бренд: Yunmai Страницы: 6

Бренд: Soehnle Professional Страницы: 56

Бренд: Eat Smart Страницы: 6

Бренд: Digi Страницы: 143

Бренд: Silvercrest Страницы: 61

Бренд: Silvercrest Страницы: 52

Бренд: Silvercrest Страницы: 54

Бренд: Silvercrest Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды