NXP Semiconductors PN7360AUEV Скачать руководство пользователя

Страница: 178 / 345

NXP Semiconductors

UM10858

PN7462 family HW user manual

UM10858

All information provided in this document is subject to legal disclaimers.

User manual
COMPANY PUBLIC

Rev. 1.4 — 14 May 2018

314514

178 of 345

Bit

Symbol

Access

Value

Description

SYNC_HIGH

R/W

0* - 1

Defines if the bit grid is fixed at maximum (1) or at a minimum
(0) value of the correlation.

FSK

R/W

0*-1

If set to 1, the demodulation scheme is FSK.

BPSK

R/W

0*-1

If set to 1, the demodulation scheme is BPSK.

Table 220. CLIF_SIGPRO_ADCBCM_THRESHOLD_REG register (address 00C0h)

* = reset value

Bit

Symbol

Access

Value

Description

31:29

RESERVED

Reserved

28:16

EDGE_DETECT_TH R/W

0000h* -
1FFFFh

Threshold for the edge decision block of the ADCBCM

15:13

RESERVED

Reserved

12:0

BIT_DETECT_TH

R/W

0000h* -
1FFFFh

Threshold for the “bit” decision block of the ADCBCM.

Table 221. CLIF_AGC_CONFIG0_REG register (address 00CCh)

* = reset value

Bit

Symbol

Access

Value

Description

INTERNAL_USE

[1]

R/W

For internal use

30:24

FOR INTERAL
USE

[1]

R/W

0*-7Fh

For internal use

23:15

INTERNAL_USE

[1]

R/W

0*-1FFh

For internal use

14:5

AGC_TIME_CONST
ANT

R/W

0*-3FFh

Time constant for the AGC update. An AGC period is given
by (AGC_TIME_C1) * 13.56 MHz

INTERNAL_USE

[1]

R/W

0*, 1

For internal use

AGC_INPUT_SEL

R/W

0*, 1

Selects the AGC value to be loaded into the AGC and the
source for manual mode:

AGC_LOAD

0*, 1

If set, one AGC control value is loaded from

AGC_MODE_SEL

R/W

0*, 1

Selects the operation mode of the AGC:

Rx-Divider is controlled by the register
CLIF_AGC_INPUT_REG.AGC_CM_VALUE or
CLIF_AGC_INPUT_REG.AGC_RM_VALUE (Dependent on
AGC_INPUT_SEL).

Rx-Divider value is controlled by the AGC.

AGC_MODE_ENABL
E

R/W

0*-1

If set, the AGC is enabled. If not set, the Rx-Divider is
controlled by either the internal AGC register or a register
value (dependent on AGC_MODE_SEL).

[1] Bit-field are either set by HAL or use default value from CLIF EEPROM default settings

Содержание PN7360AUEV


























































































































































































































































































































































Результаты поиска

Содержание PN7360AUEV

Отзывы:

Похожие инструкции для PN7360AUEV

Бренды по названию

Популярные бренды

NXP Semiconductors PN7360AUEV, Руководство пользователя

Результаты поиска

Содержание PN7360AUEV

Отзывы:

Похожие инструкции для PN7360AUEV

Бренды по названию

Популярные бренды