manualshive.com logo in svg

NXP Semiconductors PN7360AUEV, Руководство пользователя

NXP Semiconductors PN7360AUEV - инновационный продукт, который позволяет управлять электронными устройствами с удобством и безопасностью. Для получения подробной информации, скачайте бесплатное руководство пользователя с manualshive.com. Узнайте, как использовать этот продукт на максимуме его возможностей!

Поделиться
Скачать
background image

 

 

NXP Semiconductors 

UM10858 

 

PN7462 family HW user manual 

UM10858 

All information provided in this document is subject to legal disclaimers. 

© NXP B.V. 2018. All rights reserved. 

User manual                                                                                   
COMPANY PUBLIC 

Rev. 1.4 — 14 May 2018                                                                               

314514 

203 of 345 

 
 

13.  PN7462 family Contact interface 

Note: This chapter only applies to family members with contact and/or ISO7816 
interface. 

The PN7462 family integrates contact interface to enable communication with ISO7816 
and EMVCo contact smart cards, without the need for an external contact front end. It 
offers a high level of security for the cards by performing current limitation, short-circuit 
detection, ESD protection as well as supply supervision. 

PN7462 family also offer the possibility to extend the number of contact interfaces 
available, using an I/O Aux interface to connect a slot extension (TDA8007 - 2 slots, 
TDA8020 - 2 slots, TDA8026 - 5 slots). 

 

13.1  Contact interface features  

•

  Support of Class A (5), Class B (3 V) and Class C (1.8 V) contact smart cards 

•

  Compliant with ISO7816 and EMV Co 4.3 standards 

•

  Protection of the smart card 

−

  Thermal and current limitation in the event of short-circuit (pins I/O, VCC) 

−

  Vcc regulation: 5 V, 3 V, and 1.8 V 

−

  Automatic activation and deactivation sequences initiated by software, or by 

hardware in the event of a short-circuit, card take-off, overheating, falling of 
PN7462 family supply 

−

  Enhanced card-side Electro Static Discharge (ESD) protection of (>12 kV) 

−

  Supply supervisor for killing spikes during power on and off 

•

  DC-to-DC converter for VCC generation to enable support of Class A and Class B 

cards with low input voltages 

•

  Built-In debouncing on card presence contact 

•

 

 

Card Clock generation up to 13.56 MHz using the external crystal oscillator 

(27.12MHz) with synchronous frequency changes of fXTAL/2, fXTAL/3, fXTAL/4, 
fXTAL/5, fXTAL/6, fXTAL/8, fXTAL/16 

•

  Specific ISO UART with APB access for automatic convention processing, variable 

baud rate through frequency or division ratio programming, error management at 
character level for T=0 and extra guard time register 

•

  FIFO 1 to 32 characters in both reception and transmission mode 

•

  Parity error counter in reception mode and transmission mode with automatic re-

transmission 

•

  Cards clock stop (at HIGH or LOW level) 

•

  Automatic activation and deactivation sequence through a sequencer 

Содержание PN7360AUEV


























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PN7360AUEV

ABATEC A1 Installation And Operation Instruction Manual preview
A1
Бренд: ABATEC Страницы: 8
Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Бренд: Panasonic Страницы: 45
Danfoss VLT series Quick Manual preview
VLT series
Бренд: Danfoss Страницы: 37
National Instruments NI 9514 User Manual preview
NI 9514
Бренд: National Instruments Страницы: 72
Eaton EZD Series User Manual preview
EZD Series
Бренд: Eaton Страницы: 448
ADLINK Technology PCIe-8332 User Manual preview
PCIe-8332
Бренд: ADLINK Technology Страницы: 37
Oriental motor A Step AZ Series User Manual preview
A Step AZ Series
Бренд: Oriental motor Страницы: 120
Ultraflex B 301 Installation And Maintenance Manual preview
B 301
Бренд: Ultraflex Страницы: 48
OCL DLC-1.1 Quick Start Manual preview
DLC-1.1
Бренд: OCL Страницы: 2
SAMES KREMLIN LP 6 - 0.5/4 Translation From The Original Manual preview
LP 6 - 0.5/4
Бренд: SAMES KREMLIN Страницы: 5
NEC V850E/RS1 User Manual preview
V850E/RS1
Бренд: NEC Страницы: 852
SainSmart 101-40-173 Assembly preview
101-40-173
Бренд: SainSmart Страницы: 17
Pellet Grill Outlet 180-LV Installation Instructions And User Manual preview
180-LV
Бренд: Pellet Grill Outlet Страницы: 4
METRON FD4 Manual preview
FD4
Бренд: METRON Страницы: 34
Parker P3HPA Series Manual preview
P3HPA Series
Бренд: Parker Страницы: 22
VAL VLC-2430-4 Operation Manual preview
VLC-2430-4
Бренд: VAL Страницы: 10
Zonet ZUC2401 Quick Installation Manual preview
ZUC2401
Бренд: Zonet Страницы: 2
Powrmatic Eurotrol 2 Installation & User'S Instructions preview
Eurotrol 2
Бренд: Powrmatic Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды