manualshive.com logo in svg

NXP Semiconductors LPC5410x, Руководство пользователя

Микроконтроллеры NXP Semiconductors LPC5410x - мощные устройства для встроенных систем. Инструкция пользователя доступна для свободного скачивания на manualshive.com. Получите полный контроль над вашим устройством, загрузив бесплатный руководство пользователя.

Поделиться
Скачать
background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

364 of 464

NXP Semiconductors

UM10850

Chapter 25: LPC5410x 12-bit ADC controller (ADC0)

25.6 Register description

The reset value reflects the data stored in used bits only. It does not include reserved bits 
content.

 

Table 415. Register overview: ADC (base address 0x1C03 4000)

Name

Access

Address 
offset

Description

Reset 
value

Reference

CTRL

R/W

0x000

ADC Control Register. Contains the clock divide value, resolution 
selection, sampling time selection, and mode controls.

0x600

Table 416

SEQA_CTRL

R/W

0x008

ADC Conversion Sequence-A control Register: Controls 
triggering and channel selection for conversion sequence-A. Also 
specifies interrupt mode for sequence-A.

0

Table 417

SEQB_CTRL

R/W

0x00C

ADC Conversion Sequence-B Control Register: Controls 
triggering and channel selection for conversion sequence-B. Also 
specifies interrupt mode for sequence-B.

0

Table 418

SEQA_GDAT

RO

0x010

ADC Sequence-A Global Data Register. This register contains 
the result of the most recent ADC conversion performed under 
sequence-A.

NA

Table 419

SEQB_GDAT

RO

0x014

ADC Sequence-B Global Data Register. This register contains 
the result of the most recent ADC conversion performed under 
sequence-B.

NA

Table 420

DAT0

RO

0x020

ADC Channel 0 Data Register. This register contains the result of 
the most recent conversion completed on channel 0.

NA

Table 422

DAT1

RO

0x024

ADC Channel 1 Data Register. This register contains the result of 
the most recent conversion completed on channel 1.

NA

Table 422

DAT2

RO

0x028

ADC Channel 2 Data Register. This register contains the result of 
the most recent conversion completed on channel 2.

NA

Table 422

DAT3

RO

0x02C

ADC Channel 3 Data Register. This register contains the result of 
the most recent conversion completed on channel 3.

NA

Table 422

DAT4

RO

0x030

ADC Channel 4 Data Register. This register contains the result of 
the most recent conversion completed on channel 4.

NA

Table 422

DAT5

RO

0x034

ADC Channel 5 Data Register. This register contains the result of 
the most recent conversion completed on channel 5.

NA

Table 422

DAT6

RO

0x038

ADC Channel 6 Data Register. This register contains the result of 
the most recent conversion completed on channel 6.

NA

Table 422

DAT7

RO

0x03C

ADC Channel 7 Data Register. This register contains the result of 
the most recent conversion completed on channel 7.

NA

Table 422

DAT8

RO

0x040

ADC Channel 8 Data Register. This register contains the result of 
the most recent conversion completed on channel 7.

NA

Table 422

DAT9

RO

0x044

ADC Channel 9 Data Register. This register contains the result of 
the most recent conversion completed on channel 7.

NA

Table 422

DAT10

RO

0x048

ADC Channel 10 Data Register. This register contains the result 
of the most recent conversion completed on channel 7.

NA

Table 422

DAT11

RO

0x04C

ADC Channel 11 Data Register. This register contains the result 
of the most recent conversion completed on channel 7.

NA

Table 422

THR0_LOW

R/W

0x050

ADC Low Compare Threshold Register 0: Contains the lower 
threshold level for automatic threshold comparison for any 
channels linked to threshold pair 0.

0x0

Table 423

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

G1SLE MK2 Alignment Manual preview
MK2
Бренд: G1SLE Страницы: 2
E-T-A EtherNetIP ControlPlex CPC12EN User Manual preview
EtherNetIP ControlPlex CPC12EN
Бренд: E-T-A Страницы: 28
York CIW01 Installation & Maintenance Manual preview
CIW01
Бренд: York Страницы: 24
Securi-Prod LK190 Installation Manual preview
LK190
Бренд: Securi-Prod Страницы: 3
Case IH MAXXUM 100 Service Manual preview
MAXXUM 100
Бренд: Case IH Страницы: 81
Cardin Elettronica S486 Series Installation And Reference preview
S486 Series
Бренд: Cardin Elettronica Страницы: 56
Grosvenor Janus C4 485 Installation Manual preview
Janus C4 485
Бренд: Grosvenor Страницы: 5
Cypress CY8C28 series Technical Reference Manual preview
CY8C28 series
Бренд: Cypress Страницы: 571
Timotion TBB5 User Manual preview
TBB5
Бренд: Timotion Страницы: 9
Delta DZNT-104T Installation Manual preview
DZNT-104T
Бренд: Delta Страницы: 16
Burkert 8745 MFC Ethernet Operating Instructions Manual preview
8745 MFC Ethernet
Бренд: Burkert Страницы: 70
GJD DYGIZONE GJD910 Manual preview
DYGIZONE GJD910
Бренд: GJD Страницы: 13
GCE Druva MTLX Instructions For Use Manual preview
Druva MTLX
Бренд: GCE Страницы: 46
Tusa RS-790 Owner'S Manual preview
RS-790
Бренд: Tusa Страницы: 72
Danfoss 080Z0130 Manual preview
080Z0130
Бренд: Danfoss Страницы: 96
E-MAGA Interconnect BaldurTouch II Instructions Manual preview
BaldurTouch II
Бренд: E-MAGA Interconnect Страницы: 21
Dataprobe iBootBar iBP-N15 Installation And Operations preview
iBootBar iBP-N15
Бренд: Dataprobe Страницы: 21
Dometic GP-MPPT-60/10 Installation And Operating Manual preview
GP-MPPT-60/10
Бренд: Dometic Страницы: 156

Бренды по названию

Популярные бренды

Загрузить еще бренды