manualshive.com logo in svg

NXP Semiconductors LPC5410x, Руководство пользователя

Микроконтроллеры NXP Semiconductors LPC5410x - мощные устройства для встроенных систем. Инструкция пользователя доступна для свободного скачивания на manualshive.com. Получите полный контроль над вашим устройством, загрузив бесплатный руководство пользователя.

Поделиться
Скачать
background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

7 of 464

NXP Semiconductors

UM10850

Chapter 1: LPC5410x Introductory information

–

Non-maskable Interrupt (NMI) with a selection of sources.

–

Serial Wire Debug (SWD) with 4 breakpoints and 2 watchpoints.

–

System tick timer.

•

On-Chip memory:

–

Up to 512 KB on-chip flash programming memory with flash accelerator and 256 
Byte page write and erase.

–

Up to 104 KB total SRAM composed of:

–

Up to 96 KB contiguous main SRAM.

–

An additional 8 KB SRAM.

•

ROM API support:

–

Flash In-Application Programming (IAP) and In-System Programming (ISP).

–

Power Control API.

•

Serial interfaces:

–

Four USART interfaces with synchronous mode and 32 kHz mode for wake-up 
from Deep-sleep and Power-down modes. The USARTs include a FIFO buffer, and 
share a fractional baud-rate generator.

–

Two SPI interfaces, each with 4 slave selects and flexible data configuration. The 
SPIs include a FIFO buffer. Able to wake up the device from Deep-sleep and 
Power-down modes when used in slave mode.

–

Three I

2

C-bus interfaces supporting fast mode and Fast-mode Plus with data rates 

of up to 1Mbit/s and with multiple address recognition and monitor mode. Each 
I

2

C-bus interface also supports High Speed Mode as a slave. The slave function is 

able to wake up the device from Deep-sleep and Power-down modes.

•

Digital peripherals:

–

DMA controller with 22 channels and 20 programmable triggers, able to access all 
memories and DMA-capable peripherals.

–

Up to 50 General-Purpose I/O (GPIO) pins. Most GPIOs have configurable 
pull-up/pull-down resistors, open-drain mode, and input inverter.

–

GPIO registers are located on AHB for fast access.

–

Up to eight GPIOs can be selected as pin interrupts (PINT), triggered by rising, 
falling or both input edges.

–

Two GPIO grouped interrupts (GINT) enable an interrupt based on a logical 
(AND/OR) combination of input states.

–

CRC engine.

•

Timers

–

Five 32-bit standard general purpose timers/counters, four of which support up to 4 
capture inputs and 4 compare outputs, PWM mode, and external count input. 
Specific timer events can be selected to generate DMA requests. The fifth timer 
does not have external pin connections and may be used for internal timing 
operations.

–

One State Configurable Timer/PWM (SCTimer/PWM) 6 input and 8 output 
functions (including capture and match). Inputs and outputs can be routed to/from 
external pins and internally to/from selected peripherals. Internally, the SCT 
supports 13 captures/matches, 13 events and 13 states.

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

IFM CR710S Original Operating Instructions preview
CR710S
Бренд: IFM Страницы: 49
Magnescale LY71 Manual preview
LY71
Бренд: Magnescale Страницы: 3
National Instruments NI-488.2 Getting Started preview
NI-488.2
Бренд: National Instruments Страницы: 7
National Instruments GPIB-SCSI-A Installation Manual preview
GPIB-SCSI-A
Бренд: National Instruments Страницы: 16
Casambi RP GROUP Mounting Instructions preview
RP GROUP
Бренд: Casambi Страницы: 2
Ros IC-15X Operation And Maintenance Manual preview
IC-15X
Бренд: Ros Страницы: 10
TSM DOUBLER2 Instructions For Installing preview
DOUBLER2
Бренд: TSM Страницы: 2
Pegasus Astro Dual Motor Focus Controller Manual preview
Dual Motor Focus Controller
Бренд: Pegasus Astro Страницы: 16
Allen-Bradley Kinetix 350 User Manual preview
Kinetix 350
Бренд: Allen-Bradley Страницы: 162
PXM Driver LED 1x2A/48V Manual preview
Driver LED 1x2A/48V
Бренд: PXM Страницы: 11
Computherm PS Gate User Manual preview
PS Gate
Бренд: Computherm Страницы: 40
YASKAWA Sigma II Series User Manual preview
Sigma II Series
Бренд: YASKAWA Страницы: 359
Davey Torrium2 Installation And Operating Instructions Manual preview
Torrium2
Бренд: Davey Страницы: 8
Technologic TLK 43 Operating Instructions Manual preview
TLK 43
Бренд: Technologic Страницы: 21
fadini Elpro S40 Manual preview
Elpro S40
Бренд: fadini Страницы: 40
ICON ProCon C700 Series Operating Manual preview
ProCon C700 Series
Бренд: ICON Страницы: 30
Technische Alternative UVR 63 Operation & Installation Instructions preview
UVR 63
Бренд: Technische Alternative Страницы: 124
Wyrestorm NetworkHD 200 series Quick Start Manual preview
NetworkHD 200 series
Бренд: Wyrestorm Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды