manualshive.com logo in svg

NXP Semiconductors LPC5410x, Руководство пользователя

Микроконтроллеры NXP Semiconductors LPC5410x - мощные устройства для встроенных систем. Инструкция пользователя доступна для свободного скачивания на manualshive.com. Получите полный контроль над вашим устройством, загрузив бесплатный руководство пользователя.

Поделиться
Скачать
background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

371 of 464

NXP Semiconductors

UM10850

Chapter 25: LPC5410x 12-bit ADC controller (ADC0)

25.6.3 ADC Conversion Sequence B Control Register 

There are two independent conversion sequences that can be configured, each consisting 
of a set of conversions on one or more channels. This control register specifies the 
channel selection and trigger conditions for the B sequence, as well bits to allow software 
to initiate that conversion sequence.

 

Table 418: ADC Conversion Sequence B Control Register (SEQB_CTRL, address offset 0x0C) bit description

Bit

Symbol

Value Description

Reset 
value

11:0

CHANNELS

Selects which one or more of the ADC channels will be sampled and converted 
when this sequence is launched. A 1 in any bit of this field will cause the 
corresponding channel to be included in the conversion sequence, where bit 0 
corresponds to channel 0, bit 1 to channel 1 and so forth. 

When this conversion sequence is triggered, either by a hardware trigger or via 
software command, ADC conversions will be performed on each enabled channel, 
in sequence, beginning with the lowest-ordered channel.

Remark: 

 This field can ONLY be changed while SEQB_ENA (bit 31) is LOW. It is 

allowed to change this field and set bit 31 in the same write.

0x00

17:12 TRIGGER

Selects which of the available hardware trigger sources will cause this conversion 
sequence to be initiated. Program the trigger input number in this field. See 

Table 432

.

Remark: 

In order to avoid generating a spurious trigger, it is recommended writing 

to this field only when SEQB_ENA (bit 31) is low. It is safe to change this field and 
set bit 31 in the same write.

0x0

18

TRIGPOL

Select the polarity of the selected input trigger for this conversion sequence. 

Remark: 

In order to avoid generating a spurious trigger, it is recommended writing 

to this field only when SEQB_ENA (bit 31) is low. It is safe to change this field and 
set bit 31 in the same write.

0

0

Negative edge. A negative edge launches the conversion sequence on the selected 
trigger input.

1

Positive edge. A positive edge launches the conversion sequence on the selected 
trigger input.

19

SYNCBYPASS

Setting this bit allows the hardware trigger input to bypass synchronization flip-flop 
stages and therefore shorten the time between the trigger input signal and the start 
of a conversion. There are slightly different criteria for whether or not this bit can be 
set depending on the clock operating mode:

Synchronous mode (the ASYNMODE in the CTRL register = 0): Synchronization 
may be bypassed (this bit may be set) if the selected trigger source is already 
synchronous with the main system clock (eg. coming from an on-chip, 
system-clock-based timer). Whether this bit is set or not, a trigger pulse must be 
maintained for at least one system clock period.

Asynchronous mode (the ASYNMODE in the CTRL register = 1): Synchronization 
may be bypassed (this bit may be set) if it is certain that the duration of a trigger 
input pulse will be at least one cycle of the ADC clock (regardless of whether the 
trigger comes from and on-chip or off-chip source). If this bit is NOT set, the trigger 
pulse must at least be maintained for one system clock period.

0

0

Enable synchronization. The hardware trigger bypass is not enabled.

1

Bypass synchronization. The hardware trigger bypass is enabled. 

25:20 -

Reserved. Read value is undefined, only zero should be written.

N/A

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

NCR 1651 Quick Reference Manual preview
1651
Бренд: NCR Страницы: 6
Namron ZigBee Quick Start Manual preview
ZigBee
Бренд: Namron Страницы: 3
µ-Dimension D3208 User Manual preview
D3208
Бренд: µ-Dimension Страницы: 48
µ-Dimension D4006 Installation Instructions preview
D4006
Бренд: µ-Dimension Страницы: 2
Riello 20120499 Manual preview
20120499
Бренд: Riello Страницы: 72
H3C WX1804H Configuration Manual preview
WX1804H
Бренд: H3C Страницы: 11
Nanjing Putian Datang Information Electronics Co., Ltd. CL12/2410LI-A User Manual preview
CL12/2410LI-A
Бренд: Nanjing Putian Datang Information Electronics Co., Ltd. Страницы: 2
DUNIWAY Stockroom Terranova 960 Instruction Manual preview
Terranova 960
Бренд: DUNIWAY Stockroom Страницы: 30
Vexve Hydrox Series Installation, Operation And Maintenance Manual preview
Hydrox Series
Бренд: Vexve Страницы: 24
maxon motor EPOS2 24/5 Hardware Reference Manual preview
EPOS2 24/5
Бренд: maxon motor Страницы: 44
VALPES ER PLUS Installation Manual preview
ER PLUS
Бренд: VALPES Страницы: 28
C Prox Ltd DPS-T User Manual preview
DPS-T
Бренд: C Prox Ltd Страницы: 9
S&S Northern Merlin 1000VW+ Installation & Operation Manual preview
Merlin 1000VW+
Бренд: S&S Northern Страницы: 16
FuzzDog Lunar Shot Trem Quick Start Manual preview
Lunar Shot Trem
Бренд: FuzzDog Страницы: 7
Kamado Joe iKAMAND User Manual preview
iKAMAND
Бренд: Kamado Joe Страницы: 2
Belimo CQB24-3 Instruction Manual preview
CQB24-3
Бренд: Belimo Страницы: 2
VARIZOOM VZ-ROCK Operating Instructions preview
VZ-ROCK
Бренд: VARIZOOM Страницы: 2
t.a.c. DuraDrive MA40-717 Series General Instructions Manual preview
DuraDrive MA40-717 Series
Бренд: t.a.c. Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды