NXP Semiconductors LPC5410x Скачать руководство пользователя | Manualshive

Страница: 373 / 463

background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016

374 of 464

NXP Semiconductors

UM10850

Chapter 25: LPC5410x 12-bit ADC controller (ADC0)

Table 420: ADC Sequence B Global Data Register (SEQB_GDAT, address offset 0x14) bit description

Bit

Symbol

Description

Reset
value

3:0

-

Reserved.

NA

15:4

RESULT

This field contains the 12-bit ADC conversion result from the most recent conversion performed
under conversion sequence associated with this register.

The result is a binary fraction representing the voltage on the currently-selected input channel as
it falls within the range of VREFP to VREFN. Zero in the field indicates that the voltage on the
input pin was less than, equal to, or close to that on VREFN, while 0xFFF indicates that the
voltage on the input was close to, equal to, or greater than that on VREFP.

DATAVALID = 1 indicates that this result has not yet been read.

NA

17:16 THCMP

RANGE

Indicates whether the result of the last conversion performed was above, below or within the
range established by the designated threshold comparison registers (

THRn_LOW and

THRn_HIGH).

19:18 THCMP

CROSS

Indicates whether the result of the last conversion performed represented a crossing of the
threshold level established by the designated LOW threshold comparison register (

THRn_LOW)

and, if so, in what direction the crossing occurred.

25:20 -

Reserved.

NA

29:26 CHN

These bits contain the channel from which the RESULT bits were converted (e.g. 0000 identifies
channel 0, 0001 channel 1, etc.).

NA

30

OVER
RUN

This bit is set if a new conversion result is loaded into the RESULT field before a previous result
has been read - i.e. while the DATAVALID bit is set. This bit is cleared, along with the DATAVALID
bit, whenever this register is read.

This bit will contribute to an overrun interrupt/DMA trigger if the MODE bit (in SEQB_CTRL) for
the corresponding sequence is set to ‘0’ (and if the overrun interrupt is enabled).

0

31

DATA
VALID

This bit is set to ‘1’ at the end of each conversion when a new result is loaded into the RESULT
field. It is cleared whenever this register is read.

This bit will cause a conversion-complete interrupt for the corresponding sequence if the MODE
bit (in SEQB_CTRL) for that sequence is set to 0 (and if the interrupt is enabled).

0

«
...
371
372
373
374
375
...
»

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

Бренд: Microchip Technology Страницы: 37

Бренд: Calsense Страницы: 74

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Balboa Страницы: 2

Бренд: Abov Страницы: 138

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Бренд: SYCLOPE electronic Страницы: 40

Бренд: PCB Piezotronics Страницы: 12

Бренд: Qorvo Страницы: 6

Бренд: J+J Страницы: 56

Бренд: Allen-Bradley Страницы: 88

Бренд: Continental Instruments Страницы: 2

Бренд: Linear Technology Страницы: 6

Бренд: ADLINK Technology Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды