Nipro SURDIAL Скачать руководство пользователя страница 301 | Manualshive

Страница: 301 / 334

Nipro SURDIAL Скачать руководство пользователя страница 301

10.23-1

MAIN PCB

TM1

CD

T3

T2

T1

GND

W
W
R
W
W
R
W
W
R

10.23. Adjustment of conductivity sensor

Connect resistor for calibration to terminal bed on main board and adjust conductivity sensor by
volume of main board.

(1) Required device

Resistor for calibration(240

1/16W over, 360

1/16W over)

(2) Remove right cover from upper operation part and right cover from POWER box to expose

terminal bed TM1 on main board.

MAIN PCB: Main board
TM1: Terminal bed

Fig. 10.23-1 Main board and terminal bed TM1

(3)  Turn on power SW of machine.
(4)  Turn on [DIALYSIS] SW to shift to dialysis wait process.
(5)  Adjust the sensor by calibrating at two points (240  and 360 ).
(6)  Remove the conductivity sensor from the terminal block and connect the resistor for calibration.

For the connecting target, refer to Fig. 10.23-1 and Fig. 10.23-2.

240

360

switch

Fig. 10.23-2 Connection to resistor for calibration

«
...
299
300
301
302
303
...
»

Содержание SURDIAL















































































































































































































































































































































Отзывы:

Нет отзывов